Canon BJC-2000 User Manual - Page 55

Load the, first sheet., Cut the banner, at a crease, according to the, length you need.

Get Canon BJC-2000 PDF manuals and user guides View all Canon BJC-2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Cut the banner at a crease according to the length you need. r The minimum length is two sheets. r The maximum length you can use is six sheets (66 inches or 1676 mm). r Always leave an extra sheet at the end of the banner-just in case the type runs over. Load the first sheet. r Align the first sheet of the paper with the right edge of the sheet feeder and slide it into the printer until it stops. r Pinch the paper guide so it will move smoothly and slide the paper guide to the left side of the sheet. Leave a gap of about 0.04 in. (1 mm) between the paper guide and the edge of the paper. PAPER GUIDE Chapter 3 Paper Handling 3-26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
Chapter 3
Paper Handling
3-26
The minimum length is two sheets.
The maximum length you can use is six sheets (66 inches
or 1676 mm).
Always leave an extra sheet at the end of the banner—just
in case the type runs over.
Align the first sheet of the paper with the right edge of
the sheet feeder and slide it into the printer until it stops.
Pinch the paper guide so it will move smoothly and slide
the paper guide to the left side of the sheet. Leave a gap of
about 0.04 in. (1 mm) between the paper guide and the
edge of the paper.
Load the
first sheet.
Cut the banner
at a crease
according to the
length you need.
PAPER GUIDE