Cisco 7609-S Installation Guide - Page 62

Connecting the Supervisor Engine Uplink Ports

Get Cisco 7609-S PDF manuals and user guides View all Cisco 7609-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Attaching the Interface Cables Chapter 3 Installing the Cisco 7609 Internet Router Connecting the Supervisor Engine Uplink Ports This section describes how to connect to the supervisor engine uplink ports. Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures. Note In a redundant configuration with two supervisor engines, the uplink ports on the redundant (standby) supervisor engine are active and can be used for normal traffic, like any other ports in the chassis. To connect to the supervisor engine uplink ports, perform these steps: Step 1 Step 2 Remove the plugs from the Gigabit Interface Converter (GBIC) optical bores; store them for future use. Remove the plugs from the SC-type connector on the fiber-optic cable. Insert the connector into the GBIC. (See Figure 3-8.) Figure 3-8 Connecting the Supervisor Engine Uplink Ports PORT 1 LINK 48128 3-18 Cisco 7609 Internet Router Installation Guide OL-5079-04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Chapter 3
Installing the Cisco 7609 Internet Router
Attaching the Interface Cables
3-18
Cisco 7609 Internet Router Installation Guide
OL-5079-04
Connecting the Supervisor Engine Uplink Ports
This section describes how to connect to the supervisor engine uplink ports.
Warning
Because invisible laser radiation may be emitted from the aperture of the
port when no cable is connected, avoid exposure to laser radiation and do
not stare into open apertures.
Note
In a redundant configuration with two supervisor engines, the uplink ports on
the redundant (standby) supervisor engine are active and can be used for
normal traffic, like any other ports in the chassis.
To connect to the supervisor engine uplink ports, perform these steps:
Step 1
Remove the plugs from the Gigabit Interface Converter (GBIC) optical bores;
store them for future use.
Step 2
Remove the plugs from the SC-type connector on the fiber-optic cable. Insert the
connector into the GBIC. (See
Figure 3-8
.)
Figure 3-8
Connecting the Supervisor Engine Uplink Ports
LINK
PORT 1
48128