Home » Cisco Manuals » Wireless » Cisco AIR-AP1210 » Manual Viewer

Cisco AIR-AP1210 Hardware Installation Guide - Page 108

Category, Access Point with 2.4-GHz Radio, Direct Sequence Spread Spectrum DSSS

UPC - 746320804330

Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

Appendix C Access Point Specifications Table C-1 Access Point Specifications (continued) Category Power Output Frequency Range Modulation Data rates Antenna Compliance Access Point with 2.4-GHz Radio Access Point with 5-GHz Radio Module 100, 50, 30, 20, 5, or 1 mW (Depending on the regulatory domain in which the access point is installed) 40 mW (16 dBm) 20 mW (13 dBm) 10 mW (10 dBm) 5 mW (7 dBm) Note These values are based on the FCC peak measurement method as defined in FCC 15.407 (A)(4) 2.400 to 2.497 GHz (Depending on the regulatory domain in which the access point is installed) UNII 1-5.15 to 5.25 GHz UNII 2-5.25 to 5.35 GHz (Depending on the regulatory domain in which the access point is installed) Indoor: 150 ft at 11 Mbps 350 ft at 1 Mbps Outdoor: 800 ft at 11 Mbps 2000 ft at 1 Mbps Indoor: 170 ft at 6 Mbps 130 ft at 18 Mbps 60 ft at 54 Mbps Outdoor: 1000 ft at 6 Mbps 100 ft at 54 Mbps Direct Sequence Spread Spectrum (DSSS) Orthogonal Frequency Division Multiplex (OFDM) 1, 2, 5.5, and 11 Mbps 6, 9, 12, 18, 24, 36, 48, and 54 Mbps A diversity system with two reverse-TNC connectors (Cisco antennas are sold separately). A diversity system consisting of two integrated omnidirectional and two integrated directional antennas. The 1200 series access point complies with UL 2043 for products installed in a building's environmental air handling spaces, such as above suspended ceilings. Safety Caution The 1200 series power injectors are not tested to UL 2043 and should not be placed in a building's environmental air space, such as above suspended ceilings. Note If you plan to mount the access point in environmental air space using a 5-GHz radio, Cisco recommends that you mount the access point horizontally with its antennas pointing down. Doing so results in the access point complying with regulatory requirements for environmental air space with the 5-GHz radio installed. Designed to meet: Designed to meet: • UL 1950 Third Edition • UL 1950 Third Edition • CSA 22.2 No. 950-95 • CSA 22.2 No. 950-95 • IEC 60950 Second Edition, including Amendments 1-4 with all deviations • IEC 60950 Second Edition, including Amendments 1-4 with all deviations • EN 60950 Second Edition, including Amendments 1-4 • EN 60950 Second Edition, including Amendments 1-4 Cisco Aironet 1200 Series Access Point Hardware Installation Guide C-2 OL-4310-01

Section	Page
Cisco Aironet 1200 Series Access Point Hardware Installation Guide	1
Contents	3
Preface	9
Audience	9
Purpose	9
Organization	9
Conventions	10
Related Publications	12
Obtaining Documentation	12
Cisco.com	12
Documentation CD-ROM	13
Ordering Documentation	13
Documentation Feedback	13
Obtaining Technical Assistance	14
Cisco.com	14
Technical Assistance Center	14
Cisco TAC Website	15
Cisco TAC Escalation Center	15
Obtaining Additional Publications and Information	15
Overview	17
Hardware Features	18
Dual-Radio Operation	18
Ethernet Port	18
Console Port	18
LEDs	19
Power Sources	19
UL 2043 Certification	20
Anti-Theft Features	20
Network Configuration Examples	21
Root Unit on a Wired LAN	21
Repeater Unit that Extends Wireless Range	22
Central Unit in an All-Wireless Network	23
Installing the Access Point	25
Safety Information	26
FCC Safety Compliance Statement	26
General Safety Guidelines	26
Warnings	26
Unpacking the Access Point	27
Package Contents	27
Basic Installation Guidelines	27
Installation Above Suspended Ceilings	27
Before Beginning the Installation	28
Installation Summary	29
Connecting the 2.4-GHz Antennas	29
Connecting the Ethernet and Power Cables	30
Connecting to an Ethernet Network with an Inline Power Source	31
Connecting to an Ethernet Network with Local Power	31
Powering Up the Access Point	32
Configuring the Access Point for the First Time	33
Before You Start	34
Resetting the Access Point to Default Settings	34
Obtaining and Assigning an IP Address	35
Connecting to the Access Point Locally	35
Assigning Basic Settings	36
Default Settings on the Express Setup Page	40
Protecting Your Wireless LAN	40
Using the IP Setup Utility	41
Obtaining and Installing IPSU	41
Using IPSU to Find the Access Point’s IP Address	42
Using IPSU to Set the Access Point’s IP Address and SSID	43
Assigning an IP Address Using the CLI	44
Using a Telnet Session to Access the CLI	44
Using the Web-Browser Interface	45
Using the Web-Browser Interface for the First Time	46
Using the Management Pages in the Web-Browser Interface	46
Using Action Buttons	48
Character Restrictions in Entry Fields	49
Using Online Help	49
Using the Command-Line Interface	51
IOS Command Modes	52
Getting Help	53
Abbreviating Commands	53
Using no and default Forms of Commands	53
Understanding CLI Messages	54
Using Command History	54
Changing the Command History Buffer Size	54
Recalling Commands	55
Disabling the Command History Feature	55
Using Editing Features	55
Enabling and Disabling Editing Features	56
Editing Commands Through Keystrokes	56
Editing Command Lines that Wrap	57
Searching and Filtering Output of show and more Commands	58
Accessing the CLI	58
Opening the CLI with Telnet	58
Opening the CLI with Secure Shell	59
Mounting Instructions	61
Overview	62
Mounting on a Horizontal or Vertical Surface	63
Mounting on a Suspended Ceiling	64
Attaching the Access Point to the Mounting Bracket	65
Securing the Access Point to the Mounting Bracket	65
2.4-GHz Radio Upgrade	67
Upgrade Overview	68
Unpacking the Radio	68
Opening the Access Cover	69
Removing a Blank Spacer Card	70
Removing a 2.4-GHz Radio	71
Installing a 2.4-GHz Radio	73
5-GHz Radio Module Upgrade	75
Upgrade Overview	76
Unpacking the Radio Module	76
Removing the 5-GHz Radio Access Cover	76
Removing a 5-GHz Radio Module	77
Installing a 5-GHz Radio Module	79
Troubleshooting	83
Checking the Top Panel LEDs	84
Checking Basic Settings	86
SSID	86
WEP Keys	86
Security Settings	87
Resetting to the Default Configuration	87
Using the MODE Button	87
Using the Web Browser Interface	88
Reloading the Access Point Image	88
Using the MODE button	88
Web Browser Interface	89
Browser HTTP Interface	89
Browser TFTP Interface	90
Obtaining the Access Point Image File	90
Obtaining the TFTP Server Software	91
Translated Safety Warnings	93
Dipole Antenna Installation Warning	94
Explosive Device Proximity Warning	95
Lightning Activity Warning	96
Installation Warning	97
Circuit Breaker (15A) Warning	97
Declarations of Conformity and Regulatory Information	99
Manufacturers Federal Communication Commission Declaration of Conformity Statement	100
Department of Communications—Canada	101
Canadian Compliance Statement	101
European Community, Switzerland, Norway, Iceland, and Liechtenstein	102
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC	102
Declaration of Conformity for RF Exposure	104
Guidelines for Operating Cisco Aironet Access Points in Japan	104
Japanese Translation	104
English Translation	105
Access Point Specifications	107
Channels and Antenna Settings	111
Channels	112
IEEE 802.11a	112
IEEE 802.11b	113
Maximum Power Levels	114
IEEE 802.11a	114
IEEE 802.11b	114
Console Cable Pinouts	117
Overview	118
Console Port Signals and Pinouts	118
Glossary	119

Match case Limit results 1 per page

C-2

Cisco Aironet 1200 Series Access Point Hardware Installation Guide

OL-4310-01

Appendix C

Access Point Specifications

Power Output

100, 50, 30, 20, 5, or 1 mW

(Depending on the regulatory domain in

which the access point is installed)

40 mW (16 dBm)

20 mW (13 dBm)

10 mW (10 dBm)

5 mW (7 dBm)

Note

These values are based on the FCC peak

measurement method as defined in

FCC 15.407 (A)(4)

Frequency

2.400 to 2.497 GHz

(Depending on the regulatory domain in

which the access point is installed)

UNII 1

—

5.15 to 5.25 GHz

UNII 2

—

5.25 to 5.35 GHz

(Depending on the regulatory domain in which the

access point is installed)

Range

Indoor:

150 ft at 11 Mbps

350 ft at 1 Mbps

Outdoor:

800 ft at 11 Mbps

2000 ft at 1 Mbps

Indoor:

170 ft at 6 Mbps

130 ft at 18 Mbps

60 ft at 54 Mbps

Outdoor:

1000 ft at 6 Mbps

100 ft at 54 Mbps

Modulation

Direct Sequence Spread Spectrum (DSSS)

Orthogonal Frequency Division Multiplex (OFDM)

Data rates

1, 2, 5.5, and 11 Mbps

6, 9, 12, 18, 24, 36, 48, and 54 Mbps

Antenna

A diversity system with two reverse-TNC

connectors (Cisco antennas are sold

separately).

A diversity system consisting of two integrated

omnidirectional and two integrated directional

antennas.

Compliance

The 1200 series access point complies with UL 2043 for products installed in a building

’

environmental air handling spaces, such as above suspended ceilings.

Caution

The 1200 series power injectors are not tested to UL 2043 and should not be placed in a

building

’

s environmental air space, such as above suspended ceilings.

Note

If you plan to mount the access point in environmental air space using a 5-GHz radio, Cisco

recommends that you mount the access point horizontally with its antennas pointing down.

Doing so results in the access point complying with regulatory requirements for

environmental air space with the 5-GHz radio installed.

Safety

Designed to meet:

•

UL 1950 Third Edition

•

CSA 22.2 No. 950-95

•

IEC 60950 Second Edition, including

Amendments 1-4 with all deviations

•

EN 60950 Second Edition, including

Amendments 1-4