Cisco AIR-AP1220B-A-K9 Hardware Installation Guide - Page 44

No parity, Xon/Xoff, Enter, Connecting the Serial Cable

Get Cisco AIR-AP1220B-A-K9 - Aironet 1200 - Wireless Access Point PDF manuals and user guides
UPC - 746320719191
View all Cisco AIR-AP1220B-A-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Entering Basic Settings Figure 3-4 shows the location of the access point's console port. Figure 3-4 Connecting the Serial Cable Chapter 3 Basic Configuration 74005 DB-9 to RJ-45 serial cable RJ-45 serial connector Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Open your terminal emulator program. Enter these settings for the connection into your terminal emulator program: • Bits per second (baud rate): 9600 • Data bits: 8 • Parity: No parity • Stop bits: 1 • Flow control: Xon/Xoff or None Press = to display the home page of the access point. If the access point is new and its factory configuration has not been changed, the Express Setup page appears. Go to Step 5. If the access point has been configured, the Summary Status page appears. Perform the following additional steps: a. Type s and the Setup screen appears. b. Type ex and the Express Setup screen appears. c. Go to Step 5. Type na to select System Name. Enter a system name for the access point and press Enter. A descriptive system name makes it easy to identify the access point on your network. Type t and then press Enter to select Terminal Type. To specify the type of console interface, perform one of the following steps: a. Type t and then press Enter to select teletype display on the console interface. b. Type a and then press Enter to select ANSI display on the console interface. Type pr and then press Enter to select Config Server Protocol. To select the type of protocol, perform one of the following steps: • Type n to select none and press Enter after you make your selection. • Type b to select BOOTP and press Enter after you make your selection. • Type d to select DHCP and press Enter after you make your selection. 3-10 Cisco Aironet 1200 Series Access Point Hardware Installation Guide OL-2155-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
3-10
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
OL-2155-02
Chapter 3
Basic Configuration
Entering Basic Settings
Figure 3-4
shows the location of the access point
’
s console port.
Figure 3-4
Connecting the Serial Cable
Step 2
Open your terminal emulator program.
Step 3
Enter these settings for the connection into your terminal emulator program:
•
Bits per second (baud rate):
9600
•
Data bits:
8
•
Parity:
No parity
•
Stop bits:
1
•
Flow control:
Xon/Xoff
or
None
Step 4
Press
=
to display the home page of the access point.
If the access point is new and its factory configuration has not been changed, the Express Setup page
appears. Go to
Step 5
.
If the access point has been configured, the Summary Status page appears. Perform the following
additional steps:
a.
Type
s
and the Setup screen appears.
b.
Type
ex
and the Express Setup screen appears.
c.
Go to
Step 5
.
Step 5
Type
na
to select System Name. Enter a system name for the access point and press
Enter
. A descriptive
system name makes it easy to identify the access point on your network.
Step 6
Type
t
and then press
Enter
to select Terminal Type. To specify the type of console interface, perform
one of the following steps:
a.
Type
t
and then press
Enter
to select teletype display on the console interface.
b.
Type
a
and then press
Enter
to select ANSI display on the console interface.
Step 7
Type
pr
and then press
Enter
to select Config Server Protocol. To select the type of protocol, perform
one of the following steps:
•
Type
n
to select none and press
Enter
after you make your selection.
•
Type
b
to select BOOTP and press
Enter
after you make your selection.
•
Type
d
to select DHCP and press
Enter
after you make your selection.
RJ-45 serial
connector
DB-9 to RJ-45
serial cable
74005