Cisco AIR-AP1220B-A-K9 Hardware Installation Guide - Page 75

No parity, Xon/Xoff, Enter, resetall, Step 2

Get Cisco AIR-AP1220B-A-K9 - Aironet 1200 - Wireless Access Point PDF manuals and user guides
UPC - 746320719191
View all Cisco AIR-AP1220B-A-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Chapter 7 Troubleshooting Resetting to the Default Configuration Step 2 Open a terminal-emulation program on your computer. Note These instructions describe Microsoft HyperTeminal; other programs are similar. Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 In the Connection Description window, enter a name and select an icon for the connection and click OK. In the Connect To window, select the port to which the cable is connected and click OK. In the Port Settings window, enter the following settings: • Bits per second (baud rate): 9600 • Data bits: 8 • Parity: No parity • Stop bits: 1 • Flow control: Xon/Xoff or None Click OK, and press Enter. When the Summary Status screen appears, reboot the access point by unplugging the power connector or the Ethernet cable (when using in-line power) and then plugging it back in. When the access point reboots and the Summary Status screen reappears, type :resetall, and press Enter. Type yes, and press Enter to confirm the command. Note The resetall command is valid for only 2 minutes immediately after the access point reboots. If you do not enter and confirm the resetall command during that 2-minute period, reboot the access point again. Step 10 After the access point reboots and the Express Setup screen appears, reconfigure the access point by using the terminal emulator or an Internet browser. OL-2155-02 Cisco Aironet 1200 Series Access Point Hardware Installation Guide 7-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
7-5
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
OL-2155-02
Chapter 7
Troubleshooting
Resetting to the Default Configuration
Step 2
Open a terminal-emulation program on your computer.
Note
These instructions describe Microsoft HyperTeminal; other programs are similar.
Step 3
In the Connection Description window, enter a name and select an icon for the connection and click
OK
.
Step 4
In the Connect To window, select the port to which the cable is connected and click
OK
.
Step 5
In the Port Settings window, enter the following settings:
•
Bits per second (baud rate):
9600
•
Data bits:
8
•
Parity:
No parity
•
Stop bits:
1
•
Flow control:
Xon/Xoff
or
None
Step 6
Click
OK
, and press
Enter
.
Step 7
When the Summary Status screen appears, reboot the access point by unplugging the power connector
or the Ethernet cable (when using in-line power) and then plugging it back in.
Step 8
When the access point reboots and the Summary Status screen reappears, type
:resetall
, and press
Enter
.
Step 9
Type
yes
, and press
Enter
to confirm the command.
Note
The
resetall
command is valid for only 2 minutes immediately after the access point reboots. If you do
not enter and confirm the
resetall
command during that 2-minute period, reboot the access point again.
Step 10
After the access point reboots and the Express Setup screen appears, reconfigure the access point by
using the terminal emulator or an Internet browser.