Cisco WRV200 User Guide - Page 57

Configuration of PC 1 and PC 2, Configuration when Both Gateways Use Dynamic IP Addresses

Get Cisco WRV200 - Small Business Wireless-G VPN Router PDF manuals and user guides
UPC - 745883570577
View all Cisco WRV200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Appendix E Gateway-to-Gateway VPN Tunnel For the Local Security Group Type, select Subnet. Enter the RV082's local network settings in the IP Address and Subnet Mask fields. RV082 VPN Settings 8. For the Remote Security Gateway Type, select IP address. Enter the WRV200's WAN IP address in the IP Address field. 9. For the Remote Security Group Type, select Subnet. Enter the WRV200's local network settings in the IP Address and Subnet Mask fields. 10. In the IPSec Setup section, select the appropriate encryption, authentication, and other key management settings. (These should match the settings of the WRV200.) 11. In the Preshared Key field, enter a string for this key, for example, test1234. RV082 IPSec Setup Settings 12. Click Save Settings. Configuration of PC 1 and PC 2 Verify that PC 1 and PC 2 can ping each other (refer to Windows Help for more information). If the computers can ping each other, then you know the VPN tunnel is configured correctly. Configuration when Both Gateways Use Dynamic IP Addresses This example assumes both Gateways are using dynamic IP addresses. If only the Remote Gateway uses a dynamic Wireless-G VPN Router with RangeBooster IP address, refer to "Configuration when the Remote Gateway Uses a Dynamic IP." RV082 WRV200 Dynamic IP: B.B.B.B with Domain Name: www.abc.com LAN: 192.168.1.1 Dynamic IP: A.A.A.A with Domain Name: www.xyz.com LAN: 192.168.5.1 Gateway-to-Gateway IPSec VPN Tunnel - Both Gateways Using Dynamic IP NOTE: Each computer must have a network adapter installed. Configuration of the WRV200 Follow these instructions for the first VPN Router, designated WRV200. The other VPN Router is designated the RV082. 1. Launch the web browser for a networked computer, designated PC 1. 2. Access the web-based utility of the WRV200. (Refer to "Chapter 5: Configuring the Wireless-G Router" for details.) 3. Click the VPN tab. 4. Click IPSec VPN. 5. For the IPSec VPN Tunnel setting, select Enable. 6. Enter a name in the Tunnel Name field. 7. For the Local Secure Group Type, select Subnet. Enter the WRV200's local network settings in the IP Address and Mask fields. WRV200 IPSec VPN Settings 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
µ²
Gateway-to-Gateway VPN Tunnel
Wireless-G VPN Router with RangeBooster
Appendix E
For the Local Security Group Type, select
Subnet
. Enter
the RV082’s local network settings in the
IP Address 
and
Subnet Mask
fields.
RV082 VPN Settings
For the Remote Security Gateway Type, select
IP
address
. Enter the WRV200’s WAN IP address in the
IP 
Address
field.
For the Remote Security Group Type, select
Subnet
.
Enter the WRV200’s local network settings in the
IP 
Address
and
Subnet Mask
fields.
In the IPSec Setup section, select the appropriate
encryption, authentication, and other key management
settings. (These should match the settings of the
WRV200.)
In the
Preshared Key
field, enter a string for this key, for
example,
test±²³´
.
RV082 IPSec Setup Settings
Click
Save Settings
.
Configuration of PC 1 and PC 2
Verify that PC 1 and PC 2 can ping each other (refer to
Windows Help for more information). If the computers
can ping each other, then you know the VPN tunnel is
configured correctly.
Configuration when Both Gateways Use
Dynamic IP Addresses
This example assumes both Gateways are using dynamic
IP addresses. If only the Remote Gateway uses a dynamic
8.
9.
10.
11.
12.
IP address, refer to “Configuration when the Remote
Gateway Uses a Dynamic IP.”
Dynamic IP: A.A.A.A
with Domain Name:
www.xyz.com
LAN: 192.168.5.1
Dynamic IP: B.B.B.B with
Domain Name: www.abc.com
LAN: 192.168.1.1
WRV200
RV082
Gateway-to-Gateway IPSec VPN Tunnel - Both Gateways Using
Dynamic IP
NOTE:
Each computer must have a network
adapter installed.
Configuration of the WRV200
Follow these instructions for the first VPN Router,
designated WRV200. The other VPN Router is designated
the RV082.
Launch the web browser for a networked computer,
designated PC 1.
Access the web-based utility of the WRV200. (Refer
to “Chapter 5: Configuring the Wireless-G Router” for
details.)
Click the
VPN
tab.
Click
IPSec VPN
.
For the IPSec VPN Tunnel setting, select
Enable
.
Enter a name in the
Tunnel Name
field.
For the Local Secure Group Type, select
Subnet
. Enter
the WRV200’s local network settings in the
IP Address 
and
Mask 
fields.
WRV200 IPSec VPN Settings
1.
2.
3.
4.
5.
6.
7.