Dell GX260 Service Manual - Page 72

Microprocessor: Dell OptiPlex GX260 Service Manual

Get Dell GX260 - Optiplex Pentium 4 2.0GHz 512MB 40GB CD PDF manuals and user guides
UPC - 683728163389
View all Dell GX260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Back to Contents Page Microprocessor Dell™ OptiPlex™ GX260 Service Manual Removing and Installing the Heat-Sink Assembly and Microprocessor Small Form-Factor and Small Desktop Computers Small Mini-Tower Computer Small Form-Factor and Small Desktop Computers 1. Disconnect the cooling fan power cable from the FAN connector on the system board. 2. Disconnect the 12-volt power cable from the 12VPOWER connector on the system board. 3. Remove the heat sink/blower assembly. a. The heat sink is attached to the blower. Press and lower the green lever on the retention mechanism until it is parallel to the system board. b. Gently rock the heat sink, and then slightly twist it as you lift it from the microprocessor. NOTICE: Lay the heat sink down with the thermal solution facing upward. Heat Sink/Blower Assembly Removal

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Back to Contents Page
Microprocessor
Dell™ OptiPlex™ GX260 Service Manual
Removing and Installing the Heat-Sink Assembly and Microprocessor
Small Form-Factor and Small Desktop Computers
Small Mini-Tower Computer
Small Form-Factor and Small Desktop Computers
1. Disconnect the cooling fan power cable from the FAN connector on the system board.
2. Disconnect the 12-volt power cable from the 12VPOWER connector on the system board.
3. Remove the heat sink/blower assembly.
a. The heat sink is attached to the blower. Press and lower the green lever on the retention mechanism until it is
parallel to the system board.
b. Gently rock the heat sink, and then slightly twist it as you lift it from the microprocessor.
NOTICE:
Lay the heat sink down with the thermal solution facing upward.
Heat Sink/Blower Assembly Removal