Dell GX260 Service Manual - Page 90

Installing a Serial Port Adapter, Replacing the Card Cage

Get Dell GX260 - Optiplex Pentium 4 2.0GHz 512MB 40GB CD PDF manuals and user guides
UPC - 683728163389
View all Dell GX260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

b. Make sure that the riser board is fully seated in the connector on the system board. Replacing the Card Cage 1 card cage 2 tabs 3 slots 6. Reconnect any cables that you removed in step 1. 7. Connect any cables that should be attached to the card. NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. 8. Close the computer cover. 9. Attach the computer stand (optional). 10. Install any drivers required for the card as described in the card documentation. Serial Port Adapters Installing a Serial Port Adapter CAUTION: Before you perform this procedure, see "Precautionary Measures." 1. Remove the card cage (see step 1 in "Removing a PCI Card"). 2. Press the lever on the retention arm and raise the retention arm. 3. Remove the filler bracket. Raising the Retention Arm and Installing a Serial Port Adapter

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
b. Make sure that the riser board is fully seated in the connector on the system board.
Replacing the Card Cage
1
card cage
2
tabs
3
slots
6. Reconnect any cables that you removed in
step 1
.
7. Connect any cables that should be attached to the card.
NOTICE:
Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer
cover from closing properly or cause damage to the equipment.
8. Close the computer cover.
9. Attach the computer stand (optional).
10. Install any drivers required for the card as described in the card documentation.
Serial Port Adapters
Installing a Serial Port Adapter
CAUTION:
Before you perform this procedure, see "
Precautionary Measures
."
1. Remove the card cage (see
step 1
in "Removing a PCI Card").
2. Press the lever on the retention arm and raise the retention arm.
3. Remove the filler bracket.
Raising the Retention Arm and Installing a Serial Port Adapter