Dell Inspiron 2650 User Guide - Page 125

Remove the two M2.5 x 5-mm screws that secure the display-feed flex cable to

Get Dell Inspiron 2650 PDF manuals and user guides View all Dell Inspiron 2650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

Display Assembly and Display Latch: Dell Inspiron 2600 and 2650 1 top cover 2 M2.5 x 5-mm screws (2) 3 bottom case 1. Remove the keyboard. 2. Close the display assembly. 3. From the back of the computer, remove the two M2.5 x 5-mm screws labeled "circle D." 4. Open the display assembly approximately 180 degrees and support the display assembly so that it does not open past this position. 5. Remove the two M2.5 x 5-mm screws that secure the display-feed flex cable to the system board. NOTICE: When reconnecting the display-feed flex cable connector to the system board, push down on the top left and right ends of the connector. Pressing on the center of the connector may damage resistors and compromise EMI protection in the computer. file:///F|/Service%20Manuals/Dell/Inspiron/2600-50/display.htm (2 of 14) [2/28/2004 6:52:43 AM]

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
Display Assembly and Display Latch: Dell Inspiron 2600 and 2650
1
top cover
2
M2.5 x 5-mm screws (2)
3
bottom case
1.
Remove the
keyboard
.
2.
Close the display assembly.
3.
From the back of the computer, remove the two M2.5 x 5-mm screws labeled "circle D."
4.
Open the display assembly approximately 180 degrees and support the display assembly
so that it does not open past this position.
5.
Remove the two M2.5 x 5-mm screws that secure the display-feed flex cable to the
system board.
NOTICE:
When reconnecting the display-feed flex cable connector to the system board,
push down on the top left and right ends of the connector. Pressing on the center of the
connector may damage resistors and compromise EMI protection in the computer.
file:///F|/Service%20Manuals/Dell/Inspiron/2600-50/display.htm (2 of 14) [2/28/2004 6:52:43 AM]