Dell Inspiron 2650 User Guide - Page 88

Before You Remove or Replace Parts: Dell Inspiron 2600 and 2650, Preparing to Work Inside the Computer

Get Dell Inspiron 2650 PDF manuals and user guides View all Dell Inspiron 2650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Before You Remove or Replace Parts: Dell Inspiron 2600 and 2650 Back to Contents Page Before You Remove or Replace Parts Dell™ Inspiron™ 2600 and 2650 Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Preparing to Work Inside the Computer CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow applicable safety instructions in the Owner's Manual that came with the computer. NOTICE: To avoid damaging the computer, perform the following steps before you begin working inside the computer. 1. Ensure that the work surface is flat and clean to prevent scratching the computer cover. 2. Save any work in progress and exit all open programs. HINT: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the computer operating system, press and hold the power button for 4 seconds. 3. Turn off the computer and all attached devices. 4. Disconnect the computer from the electrical outlet. 5. To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any attached devices. file:///F|/Service%20Manuals/Dell/Inspiron/2600-50/begin.htm (1 of 8) [2/28/2004 6:52:38 AM]

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
Before You Remove or Replace Parts: Dell Inspiron 2600 and 2650
Back to Contents Page
Before You Remove or Replace Parts
Dell™ Inspiron™ 2600 and 2650
Preparing to Work Inside the Computer
Recommended Tools
Computer Orientation
Screw Identification
Preparing to Work Inside the Computer
CAUTION:
Only a certified service technician should perform repairs on
your computer. Damage due to servicing that is not authorized by Dell
is not covered by your warranty. Read and follow applicable safety
instructions in the
Owner's Manual
that came with the computer.
NOTICE:
To avoid damaging the computer, perform the following steps before
you begin working inside the computer.
1.
Ensure that the work surface is flat and clean to prevent scratching the
computer cover.
2.
Save any work in progress and exit all open programs.
HINT:
Ensure that the computer is off and not in a power management mode. If
you cannot shut down the computer using the computer operating system, press
and hold the power button for 4 seconds.
3.
Turn off the computer and all attached devices.
4.
Disconnect the computer from the electrical outlet.
5.
To avoid possible damage to the system board, wait 10 to 20 seconds and then
disconnect any attached devices.
file:///F|/Service%20Manuals/Dell/Inspiron/2600-50/begin.htm (1 of 8) [2/28/2004 6:52:38 AM]