Dell OptiPlex 7010 Owner's Manual (Mini-Tower) - Page 52

WARNING: Dell's Disk Monitoring, System Setup program - monitor support

Get Dell OptiPlex 7010 PDF manuals and user guides View all Dell OptiPlex 7010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Error Message Description Plug and play configuration error The computer encountered a problem while trying to configure one or more cards. Read fault The operating system cannot read from the floppy or hard drive, the computer could not find a particular sector on the disk, or the requested sector is defective. Requested sector not found The operating system cannot read from the floppy or hard drive, the computer could not find a particular sector on the disk, or the requested sector is defective. Reset failed The disk re-set operation failed. Sector not found The operating system cannot locate a sector on the floppy or hard drive. Seek error The operating system cannot find a specific track on the floppy disk or hard drive. Shutdown failure A chip on the system board might be malfunctioning. Time-of-day clock stopped The battery might be dead. Time-of-day not set-please run the System Setup program The time or date stored in System Setup does not match the computer clock. Timer chip counter 2 failed A chip on the system board may be malfunctioning. Unexpected interrupt in protected mode The keyboard controller may be malfunctioning or a memory module may be loose. WARNING: Dell's Disk Monitoring During initial startup, the drive detected possible error conditions. When your System has detected that drive [0/1] on computer finishes booting, immediately back up your data and replace your the [primary/secondary] EIDE hard drive (for installation procedures, see "Adding and Removing Parts" for controller is operating outside of your computer type). If no replacement drive is immediately available and the normal specifications. It is advisable to drive is not the only bootable drive, enter System Setup and change the immediately back up your data and appropriate drive setting to None. Then remove the drive from the computer. replace your hard drive by calling your support desk or Dell. Write fault The operating system cannot write to the floppy or hard drive. Write fault on selected drive The operating system cannot write to the floppy or hard drive. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
Error Message
Description
Plug and play configuration error
The computer encountered a problem while trying to configure one or more
cards.
Read fault
The operating system cannot read from the floppy or hard drive, the computer
could not find a particular sector on the disk, or the requested sector is
defective.
Requested sector not found
The operating system cannot read from the floppy or hard drive, the computer
could not find a particular sector on the disk, or the requested sector is
defective.
Reset failed
The disk re-set operation failed.
Sector not found
The operating system cannot locate a sector on the floppy or hard drive.
Seek error
The operating system cannot find a specific track on the floppy disk or hard
drive.
Shutdown failure
A chip on the system board might be malfunctioning.
Time-of-day clock stopped
The battery might be dead.
Time-of-day not set-please run the
System Setup program
The time or date stored in System Setup does not match the computer clock.
Timer chip counter 2 failed
A chip on the system board may be malfunctioning.
Unexpected interrupt in protected
mode
The keyboard controller may be malfunctioning or a memory module may be
loose.
WARNING: Dell's Disk Monitoring
System has detected that drive [0/1] on
the [primary/secondary] EIDE
controller is operating outside of
normal specifications. It is advisable to
immediately back up your data and
replace your hard drive by calling your
support desk or Dell.
During initial startup, the drive detected possible error conditions. When your
computer finishes booting, immediately back up your data and replace your
hard drive (for installation procedures, see "Adding and Removing Parts" for
your computer type). If no replacement drive is immediately available and the
drive is not the only bootable drive, enter System Setup and change the
appropriate drive setting to
None
. Then remove the drive from the computer.
Write fault
The operating system cannot write to the floppy or hard drive.
Write fault on selected drive
The operating system cannot write to the floppy or hard drive.
52