Dell S4112F EMC S4112–ON Series Installation Guide October 2021 - Page 35

eth0 Link encap:Ethernet HWaddr 90:B1:1C:F4:9C:76, UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

Get Dell S4112F PDF manuals and user guides View all Dell S4112F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

1. Search locally attached storage devices for one of the ONIE default installer filenames-for example, the filename is: onie self update from the USB. 2. Search locally attached storage devices for one of the ONIE default installer filenames-for example, USB. 3. Query to the IPv4 and IPv6 link-local neighbors using HTTP for an installer. 4. Discover TFTP-based image from the DHCP server. If none of the ONIE Service Discovery methods are successful, you can disable this using the onie-discovery-stop command. You can install an operating system manually from HTTP, FTP, or TFTP using the onie-nos-install command. NOTE: If you have a recovery USB plugged into your switch, remove it before installing the DIAG-OS using the onienos-install command. The ONIE Install environment uses DHCP to assign an IP address to the management interface-eth0. If that fails, it uses the default IP address 192.168.3.10/255.255.255.0. To display the IP address, use the ifconfig eth0 command, as shown. ONIE:/ # ifconfig eth0 eth0 Link encap:Ethernet HWaddr 90:B1:1C:F4:9C:76 inet addr:10.11.53.33 Bcast:10.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::92b1:1cff:fef4:9c76/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1152 (1.1 KiB) TX bytes:6864 (6.7 KiB) Interrupt:21 Memory:ff300000-ff320000 To assign an IP address to the management interface, eth0, and verify network connectivity, use the ifconfig eth0 command, as shown. ONIE:/ # ifconfig eth0 10.11.53.33/16 Verify the network connection with ping. ONIE:/ # ping 10.11.8.12 PING 10.11.8.12 (10.11.8.12): 56 data bytes 64 bytes from 10.11.8.12: seq=0 ttl=62 time=1.357 ms 64 bytes from 10.11.8.12: seq=1 ttl=62 time=0.577 ms ^C Management ports 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
1.
Search locally attached storage devices for one of the ONIE default installer filenames—for example, the filename is:
onie
self update
from the USB.
2.
Search locally attached storage devices for one of the ONIE default installer filenames—for example, USB.
3.
Query to the IPv4 and IPv6 link-local neighbors using HTTP for an installer.
4.
Discover TFTP-based image from the DHCP server.
If none of the ONIE Service Discovery methods are successful, you can disable this using the
onie-discovery-stop
command.
You can install an operating system manually from HTTP, FTP, or TFTP using the
onie-nos-install <URL>
command.
NOTE:
If you have a recovery USB plugged into your switch, remove it before installing the DIAG-OS using the
onie-
nos-install
command.
The ONIE Install environment uses DHCP to assign an IP address to the management interface—
eth0
. If that fails, it uses the
default IP address 192.168.3.10/255.255.255.0.
To display the IP address, use the
ifconfig eth0
command, as shown.
ONIE:/ # ifconfig eth0
eth0 Link encap:Ethernet HWaddr 90:B1:1C:F4:9C:76
inet addr:10.11.53.33 Bcast:10.255.255.255 Mask:255.0.0.0
inet6 addr: fe80::92b1:1cff:fef4:9c76/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:1152 (1.1 KiB) TX bytes:6864 (6.7 KiB)
Interrupt:21 Memory:ff300000-ff320000
To assign an IP address to the management interface,
eth0
, and verify network connectivity, use the
ifconfig eth0
<ip
address>
command, as shown.
ONIE:/ # ifconfig eth0 10.11.53.33/16
Verify the network connection with ping.
ONIE:/ # ping 10.11.8.12
PING 10.11.8.12 (10.11.8.12): 56 data bytes
64 bytes from 10.11.8.12: seq=0 ttl=62 time=1.357 ms
64 bytes from 10.11.8.12: seq=1 ttl=62 time=0.577 ms
^C
Management ports
35