Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 24

Con VLT

Page 24 highlights

S5148F-Leaf1A switchport trunk allowed vlan 16121615 spanning-tree port type edge flowcontrol receive on flowcontrol transmit off no shutdown interface ethernet1/1/19 description Node3_Port1 switchport mode trunk switchport access vlan 1611 switchport trunk allowed vlan 16121615 spanning-tree port type edge flowcontrol receive on flowcontrol transmit off no shutdown interface ethernet1/1/20 description Node4_Port1 switchport mode trunk switchport access vlan 1611 switchport trunk allowed vlan 16121615 spanning-tree port type edge flowcontrol receive on flowcontrol transmit off no shutdown S5148F-Leaf1B switchport trunk allowed vlan 16121615 spanning-tree port type edge flowcontrol receive on flowcontrol transmit off no shutdown interface ethernet1/1/19 description Node3_Port2 switchport mode trunk switchport access vlan 1611 switchport trunk allowed vlan 16121615 spanning-tree port type edge flowcontrol receive on flowcontrol transmit off no shutdown interface ethernet1/1/20 description Node4_Port2 switchport mode trunk switchport access vlan 1611 switchport trunk allowed vlan 16121615 spanning-tree port type edge flowcontrol receive on flowcontrol transmit off no shutdown 7.1.4 Configure VLT Use 100GbE interfaces for the VLTi between the two leaf switches. This example uses interfaces 1/1/53 and 1/1/54. Remove each interface from Layer 2 mode with the no switchport command. Create the VLT domain. The backup destination is the OOB management IP address of the VLT peer switch. Configure the interfaces used as the VLTi with the discovery-interface command. Enable peer routing. Note: For more information on VLT, see the OS10 Enterprise Edition User Guide Release 10.4.1.0. When the configuration is complete, exit configuration mode and save the configuration with the end and write memory commands. Configure VLT - dual switch with VLT S5148F-Leaf1A interface ethernet1/1/53 description VLTi no switchport no shutdown S5148F-Leaf1B interface ethernet1/1/53 description VLTi no switchport no shutdown interface ethernet1/1/54 description VLTi no switchport no shutdown interface ethernet1/1/54 description VLTi no switchport no shutdown 24 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46

24
Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5
S5148F-Leaf1A
S5148F-Leaf1B
switchport trunk allowed vlan 1612-
1615
spanning-tree port type edge
flowcontrol receive on
flowcontrol transmit off
no shutdown
interface ethernet1/1/19
description Node3_Port1
switchport mode trunk
switchport access vlan 1611
switchport trunk allowed vlan 1612-
1615
spanning-tree port type edge
flowcontrol receive on
flowcontrol transmit off
no shutdown
interface ethernet1/1/20
description Node4_Port1
switchport mode trunk
switchport access vlan 1611
switchport trunk allowed vlan 1612-
1615
spanning-tree port type edge
flowcontrol receive on
flowcontrol transmit off
no shutdown
switchport trunk allowed vlan 1612-
1615
spanning-tree port type edge
flowcontrol receive on
flowcontrol transmit off
no shutdown
interface ethernet1/1/19
description Node3_Port2
switchport mode trunk
switchport access vlan 1611
switchport trunk allowed vlan 1612-
1615
spanning-tree port type edge
flowcontrol receive on
flowcontrol transmit off
no shutdown
interface ethernet1/1/20
description Node4_Port2
switchport mode trunk
switchport access vlan 1611
switchport trunk allowed vlan 1612-
1615
spanning-tree port type edge
flowcontrol receive on
flowcontrol transmit off
no shutdown
7.1.4
Configure VLT
Use 100GbE interfaces for the VLTi between the two leaf switches. This example uses interfaces 1/1/53 and
1/1/54. Remove each interface from Layer 2 mode with the
no switchport
command.
Create the VLT domain. The backup destination is the OOB management IP address of the VLT peer switch.
Configure the interfaces used as the VLTi with the
discovery-interface
command. Enable peer routing.
Note:
For more information on VLT, see the
OS10 Enterprise Edition User Guide Release 10.4.1.0
.
When the configuration is complete, exit configuration mode and save the configuration with the
end
and
write memory
commands.
Configure VLT
dual switch with VLT
S5148F-Leaf1A
S5148F-Leaf1B
interface ethernet1/1/53
description VLTi
no switchport
no shutdown
interface ethernet1/1/54
description VLTi
no switchport
no shutdown
interface ethernet1/1/53
description VLTi
no switchport
no shutdown
interface ethernet1/1/54
description VLTi
no switchport
no shutdown