Home » Dell Manuals » Hubs & Switches » Dell S5148F-ON » Manual Viewer

Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 38

show vlt, backup-link, mismatch

Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

8.2.2 show vlt domain_id backup-link This command is used to verify VLT peers are communicating on the backup link over the OOB management network. The Destination is the management IP address of the peer. The Peer HeartBeat status must be Up. S5148F-Leaf1A#show vlt 127 backup-link VLT Backup Link Destination : 100.67.172.37 Peer Heartbeat status : Up Heartbeat interval : 30 Heartbeat timeout : 90 8.2.3 show vlt domain_id mismatch This command highlights any potential configuration issues between VLT peers. All items must indicate No mismatch. S5148F-Leaf1A#show vlt 127 mismatch VLT-MAC mismatch: No mismatch Peer-routing mismatch: No mismatch VLAN mismatch: No mismatch VLT VLAN mismatch: No mismatch 38 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5

Section	Page
1 Introduction	5
1.1 Supported switches and operating systems	6
1.2 Typographical conventions	6
1.3 Attachments	6
2 Hardware overview	7
2.1 Dell EMC PowerSwitch S5148F-ON	7
2.2 Dell EMC PowerSwitch S3048-ON	7
2.3 Dell EMC VxRail 14G nodes	7
2.3.1 Dell EMC VxRail P Series node	8
2.3.2 Dell EMC VxRail V Series node	8
2.3.3 Dell EMC VxRail S Series node	8
2.3.4 Dell EMC VxRail E Series node	8
2.3.5 VxRail node network adapters	8
3 Topology options	10
3.1 Dual switch	10
3.1.1 Dual switch with VLT	10
3.1.2 Dual switch without VLT	11
3.2 Single switch	12
4 VxRail in the data center	13
4.1 Leaf-spine network	13
4.2 OOB management network	14
5 Configuration planning	15
5.1 VLANs and IP addresses	15
5.2 VxRail network configuration table	16
5.3 Using a jump box or laptop computer	17
5.4 DNS and NTP servers	17
6 Switch configuration prerequisites	19
6.1 Check switch OS version	19
6.2 Verify license installation	19
6.3 Factory default configuration	20
7 Configure switches	21
7.1 Dual switch with VLT	21
7.1.1 General settings	21
7.1.2 Configure VLANs	22
7.1.3 Configure interfaces	23
7.1.4 Configure VLT	24
7.2 Dual switch without VLT	25
7.2.1 General settings	26
7.2.2 Configure VLANs	26
7.2.3 Configure interfaces	27
7.2.4 Configure the switch interconnect	28
7.3 Single switch	29
7.3.1 General settings	30
7.3.2 Configure VLANs	30
7.3.3 Configure interfaces	31
8 Switch validation	34
8.1 General validation commands	34
8.1.1 show interface status	34
8.1.2 show port-channel summary	34
8.1.3 show vlan	35
8.1.4 show lldp neighbors	36
8.1.5 show vrrp brief	37
8.2 VLT validation commands	37
8.2.1 show vlt domain_id	37
8.2.2 show vlt domain_id backup-link	38
8.2.3 show vlt domain_id mismatch	38
9 Deploy VxRail	39
A Validated components for S5148F-ON using VxRail 4.5	41
A.1 Dell EMC PowerSwitches	41
A.2 DAC Cables	41
A.3 VxRail P570 nodes	41
A.4 VxRail Appliance software	42
B VxRail network adapter traffic optimization	43
C VxRail node discovery troubleshooting	44
D Technical resources	45