Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 34

Switch validation

Get Dell S5148F-ON PDF manuals and user guides View all Dell S5148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

8 Switch validation After switches are configured and devices are connected, the switch CLI is used to validate the network configuration. This section provides a list of the most common commands and their output for the examples used in this guide. 8.1 General validation commands The commands and output shown below are for S5148F-Leaf1A in the dual switch with VLT topology. The output of its peer, S5148F-Leaf1B, is similar. If the dual switch without VLT or single switch topology is used, notes are added where differences exist. Note: For additional commands and output related to the leaf-spine portion of the topology, such as BGP and Uplink Failure Detection (UFD), see Dell EMC Networking Layer 3 Leaf-Spine Deployment and Best Practices with OS10EE. 8.1.1 show interface status The show interface status | grep up command is used to verify required interfaces are up, and links are established at their appropriate speeds. S5148F-Leaf1A#show interface status | grep up Port Description Status Speed Eth 1/1/9 JumpBox_DNS up 10G Eth 1/1/17 Node1_Port1 up 25G Eth 1/1/18 Node2_Port1 up 25G Eth 1/1/19 Node3_Port1 up 25G Eth 1/1/20 Node4_Port1 up 25G Eth 1/1/53 VLTi up 100G Eth 1/1/54 VLTi up 100G Duplex full full full full full full full Mode Vlan Tagged-Vlans A 1611 T 1611 1612-1615 T 1611 1612-1615 T 1611 1612-1615 T 1611 1612-1615 - Note: For the dual switch without VLT topology, the output is identical to the above except for the description of ports 1/1/53-54. For the single switch topology, the output includes all eight node ports, and ports 1/1/53-54 are not used. 8.1.2 show port-channel summary The show port-channel summary command is used to view port channel numbers, interfaces used, and status. In OS10EE, the VLTi is automatically configured as a static LAG using port channel 1000. Ports 1/1/53 and 1/1/54 are port channel members and (P) indicates each is up and active. S5148F-Leaf1A#show port-channel summary Flags: D - Down I - member up but inactive P - member up and active U - Up (port-channel) F - Fallback Activated Group Port-Channel Type Protocol Member Ports 1000 port-channel1000 Eth STATIC 1/1/53(P) 1/1/54(P) 34 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
34
Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5
8
Switch validation
After switches are configured and devices are connected, the switch CLI is used to validate the network
configuration. This section provides a list of the most common commands and their output for the examples
used in this guide.
8.1
General validation commands
The commands and output shown below are for S5148F-Leaf1A in the dual switch with VLT topology. The
output of its peer, S5148F-Leaf1B, is similar. If the dual switch without VLT or single switch topology is used,
notes are added where differences exist.
Note:
For additional commands and output related to the leaf-spine portion of the topology, such as BGP and
Uplink Failure Detection (UFD), see
Dell EMC Networking Layer 3 Leaf-Spine Deployment and Best Practices
with OS10EE
.
8.1.1
show interface status
The
show interface status | grep up
command is used to verify required interfaces are up, and
links are established at their appropriate speeds.
S5148F-Leaf1A#
show interface status | grep up
Port
Description
Status
Speed
Duplex
Mode Vlan Tagged-Vlans
Eth 1/1/9
JumpBox_DNS
up
10G
full
A
1611 -
Eth 1/1/17
Node1_Port1
up
25G
full
T
1611 1612-1615
Eth 1/1/18
Node2_Port1
up
25G
full
T
1611 1612-1615
Eth 1/1/19
Node3_Port1
up
25G
full
T
1611 1612-1615
Eth 1/1/20
Node4_Port1
up
25G
full
T
1611 1612-1615
Eth 1/1/53
VLTi
up
100G
full
-
Eth 1/1/54
VLTi
up
100G
full
-
Note:
For the dual switch without VLT topology, the output is identical to the above except for the description
of ports 1/1/53-54. For the single switch topology, the output includes all eight node ports, and ports 1/1/53-54
are not used.
8.1.2
show port-channel summary
The
show port-channel summary
command is used to view port channel numbers, interfaces used, and
status. In OS10EE, the VLTi is automatically configured as a static LAG using port channel 1000. Ports 1/1/53
and 1/1/54 are port channel members and
(P)
indicates each is up and active.
S5148F-Leaf1A#
show port-channel summary
Flags:
D - Down
I - member up but inactive
P - member up and active
U - Up (port-channel)
F - Fallback Activated
--------------------------------------------------------------------------------
Group Port-Channel
Type
Protocol
Member Ports
--------------------------------------------------------------------------------
1000 port-channel1000
Eth
STATIC
1/1/53(P) 1/1/54(P)