Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 26

General settings, Con VLANs

Get Dell S5148F-ON PDF manuals and user guides View all Dell S5148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Note: The commands in the tables below should be entered in the order shown. All commands are provided in the file attachments named S5148F-1A-no-vlt.txt and S5148F-1B-no-vlt.txt. 7.2.1 General settings Configure the hostname, OOB management IP address, and default gateway. Specify an NTP server accessible by the switch. In this example, this is an NTP server on the OOB management network, with a different IP address than the one used by the VxRail nodes on the in-band management network. Note: Default spanning tree settings are used in this deployment. In OS10EE, RVPST+ is enabled by default, and RPVST+ VLAN priority numbers start at 32769. Modify the spanning tree settings if required for your environment. LLDP is enabled on each interface and globally by default. LLDP is useful for troubleshooting and validation. Dell EMC recommends leaving it enabled. General settings - dual switch without VLT S5148F-Leaf1A S5148F-Leaf1B configure terminal configure terminal hostname S5148F-Leaf1A hostname S5148F-Leaf1B interface mgmt1/1/1 no ip address ip address 100.67.172.38/24 no shutdown management route 0.0.0.0/0 100.67.172.254 interface mgmt1/1/1 no ip address ip address 100.67.172.37/24 no shutdown management route 0.0.0.0/0 100.67.172.254 ntp server 100.67.10.20 ntp server 100.67.10.20 7.2.2 Configure VLANs In this section, VLANs are configured per Table 2. Create the in-band management VLAN and assign a unique IP address on each switch. Configure VRRP to provide gateway redundancy. Set the VRRP priority. The switch with the largest priority value becomes the master VRRP router. Assign the same virtual address to both switches. Create the vMotion, vSAN, and VM Network VLANs. Configure VLANs - dual switch without VLT S5148F-Leaf1A S5148F-Leaf1B interface vlan1611 description InBand_Mgmt ip address 172.16.11.253/24 vrrp-group 11 priority 150 virtual-address 172.16.11.254 no shutdown interface vlan1611 description InBand_Mgmt ip address 172.16.11.252/24 vrrp-group 11 priority 100 virtual-address 172.16.11.254 no shutdown interface vlan1612 description vMotion interface vlan1612 description vMotion 26 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
26
Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5
Note:
The commands in the tables below should be entered in the order shown. All commands are provided
in the file attachments named S5148F-1A-no-vlt.txt and S5148F-1B-no-vlt.txt.
7.2.1
General settings
Configure the hostname, OOB management IP address, and default gateway. Specify an NTP server
accessible by the switch. In this example, this is an NTP server on the OOB management network, with a
different IP address than the one used by the VxRail nodes on the in-band management network.
Note:
Default spanning tree settings are used in this deployment. In OS10EE, RVPST+ is enabled by default,
and RPVST+ VLAN priority numbers start at 32769. Modify the spanning tree settings if required for your
environment. LLDP is enabled on each interface and globally by default. LLDP is useful for troubleshooting
and validation. Dell EMC recommends leaving it enabled.
General settings - dual switch without VLT
S5148F-Leaf1A
S5148F-Leaf1B
configure terminal
hostname S5148F-Leaf1A
interface mgmt1/1/1
no ip address
ip address 100.67.172.38/24
no shutdown
management route 0.0.0.0/0
100.67.172.254
ntp server 100.67.10.20
configure terminal
hostname S5148F-Leaf1B
interface mgmt1/1/1
no ip address
ip address 100.67.172.37/24
no shutdown
management route 0.0.0.0/0
100.67.172.254
ntp server 100.67.10.20
7.2.2
Configure VLANs
In this section, VLANs are configured per Table 2.
Create the in-band management VLAN and assign a unique IP address on each switch. Configure VRRP to
provide gateway redundancy. Set the VRRP priority. The switch with the largest priority value becomes the
master VRRP router. Assign the same virtual address to both switches.
Create the vMotion, vSAN, and VM Network VLANs.
Configure VLANs - dual switch without VLT
S5148F-Leaf1A
S5148F-Leaf1B
interface vlan1611
description InBand_Mgmt
ip address 172.16.11.253/24
vrrp-group 11
priority 150
virtual-address 172.16.11.254
no shutdown
interface vlan1612
description vMotion
interface vlan1611
description InBand_Mgmt
ip address 172.16.11.252/24
vrrp-group 11
priority 100
virtual-address 172.16.11.254
no shutdown
interface vlan1612
description vMotion