Home » Dell Manuals » Hubs & Switches » Dell S5148F-ON » Manual Viewer

Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 41

Validated components for S5148F-ON using VxRail 4.5 - firmware

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

A A.1 A.2 Validated components for S5148F-ON using VxRail 4.5 The following tables include the hardware, software, and firmware used to configure and validate the examples in this guide. Dell EMC PowerSwitches Switches and OS versions Qty Item 2 Dell EMC PowerSwitch S5148F-ON leaf switches 1 Dell EMC PowerSwitch S3048-ON management switch OS Version 10.4.1.1 10.4.1.1 DAC Cables DAC cables used to connect nodes to ToR Qty Item 8 DAC-SFP28-25G-3.0M Dell PN 0VXFJY A.3 Note: VxRail support for 25GbE fiber optic cables requires VxRail release 4.5.215 and later. VxRail releases 4.5.200 through 4.5.214 require the use of DAC cables in a 25GbE configuration. VxRail P570 nodes A cluster of four VxRail P570 nodes was used to validate the examples in this guide. The nodes were each configured, as shown in the table below. Qty per node 2 12 3 10 1 1 1 - VxRail P570 node components Item Firmware version Intel Xeon Gold 6136 CPU @ 3.00GHz, 12 cores 16GB DDR4 DIMMs (192GB total) 800GB SAS SSD 1.2TB SAS HDD Dell HBA330 Storage Controller 13.17.03.05 Boot Optimized Storage Solution (BOSS) Controller w/ 2x240GB 2.5.13.2008 SATA SSDs Broadcom 57414 rNDC - 2x25GbE SFP28 ports 20.06.05.11 BIOS 1.2.11 iDRAC with Lifecycle Controller 3.15.17.15 41 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5

Section	Page
1 Introduction	5
1.1 Supported switches and operating systems	6
1.2 Typographical conventions	6
1.3 Attachments	6
2 Hardware overview	7
2.1 Dell EMC PowerSwitch S5148F-ON	7
2.2 Dell EMC PowerSwitch S3048-ON	7
2.3 Dell EMC VxRail 14G nodes	7
2.3.1 Dell EMC VxRail P Series node	8
2.3.2 Dell EMC VxRail V Series node	8
2.3.3 Dell EMC VxRail S Series node	8
2.3.4 Dell EMC VxRail E Series node	8
2.3.5 VxRail node network adapters	8
3 Topology options	10
3.1 Dual switch	10
3.1.1 Dual switch with VLT	10
3.1.2 Dual switch without VLT	11
3.2 Single switch	12
4 VxRail in the data center	13
4.1 Leaf-spine network	13
4.2 OOB management network	14
5 Configuration planning	15
5.1 VLANs and IP addresses	15
5.2 VxRail network configuration table	16
5.3 Using a jump box or laptop computer	17
5.4 DNS and NTP servers	17
6 Switch configuration prerequisites	19
6.1 Check switch OS version	19
6.2 Verify license installation	19
6.3 Factory default configuration	20
7 Configure switches	21
7.1 Dual switch with VLT	21
7.1.1 General settings	21
7.1.2 Configure VLANs	22
7.1.3 Configure interfaces	23
7.1.4 Configure VLT	24
7.2 Dual switch without VLT	25
7.2.1 General settings	26
7.2.2 Configure VLANs	26
7.2.3 Configure interfaces	27
7.2.4 Configure the switch interconnect	28
7.3 Single switch	29
7.3.1 General settings	30
7.3.2 Configure VLANs	30
7.3.3 Configure interfaces	31
8 Switch validation	34
8.1 General validation commands	34
8.1.1 show interface status	34
8.1.2 show port-channel summary	34
8.1.3 show vlan	35
8.1.4 show lldp neighbors	36
8.1.5 show vrrp brief	37
8.2 VLT validation commands	37
8.2.1 show vlt domain_id	37
8.2.2 show vlt domain_id backup-link	38
8.2.3 show vlt domain_id mismatch	38
9 Deploy VxRail	39
A Validated components for S5148F-ON using VxRail 4.5	41
A.1 Dell EMC PowerSwitches	41
A.2 DAC Cables	41
A.3 VxRail P570 nodes	41
A.4 VxRail Appliance software	42
B VxRail network adapter traffic optimization	43
C VxRail node discovery troubleshooting	44
D Technical resources	45