Home » Dell Manuals » Hubs & Switches » Dell S5148F-ON » Manual Viewer

Dell S5148F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 42

VxRail Appliance software

Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

A.4 VxRail Appliance software The examples using S5148F-ON in this guide were developed using VxRail Appliance software 4.5.200. It consists of the component versions shown below. VxRail Appliance software component versions Item Version VxRail Manager 4.5.200.7769314 VMware ESXi 6.5.0 Update 1 Patch 36, build 7388607 VMware vCenter Server Appliance 6.5 Update 1e, build 7515524 VMware vSAN 6.6.1 Patch 02 VMware vRealize Log Insight 4.3, build 5084751 42 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail 4.5

Section	Page
1 Introduction	5
1.1 Supported switches and operating systems	6
1.2 Typographical conventions	6
1.3 Attachments	6
2 Hardware overview	7
2.1 Dell EMC PowerSwitch S5148F-ON	7
2.2 Dell EMC PowerSwitch S3048-ON	7
2.3 Dell EMC VxRail 14G nodes	7
2.3.1 Dell EMC VxRail P Series node	8
2.3.2 Dell EMC VxRail V Series node	8
2.3.3 Dell EMC VxRail S Series node	8
2.3.4 Dell EMC VxRail E Series node	8
2.3.5 VxRail node network adapters	8
3 Topology options	10
3.1 Dual switch	10
3.1.1 Dual switch with VLT	10
3.1.2 Dual switch without VLT	11
3.2 Single switch	12
4 VxRail in the data center	13
4.1 Leaf-spine network	13
4.2 OOB management network	14
5 Configuration planning	15
5.1 VLANs and IP addresses	15
5.2 VxRail network configuration table	16
5.3 Using a jump box or laptop computer	17
5.4 DNS and NTP servers	17
6 Switch configuration prerequisites	19
6.1 Check switch OS version	19
6.2 Verify license installation	19
6.3 Factory default configuration	20
7 Configure switches	21
7.1 Dual switch with VLT	21
7.1.1 General settings	21
7.1.2 Configure VLANs	22
7.1.3 Configure interfaces	23
7.1.4 Configure VLT	24
7.2 Dual switch without VLT	25
7.2.1 General settings	26
7.2.2 Configure VLANs	26
7.2.3 Configure interfaces	27
7.2.4 Configure the switch interconnect	28
7.3 Single switch	29
7.3.1 General settings	30
7.3.2 Configure VLANs	30
7.3.3 Configure interfaces	31
8 Switch validation	34
8.1 General validation commands	34
8.1.1 show interface status	34
8.1.2 show port-channel summary	34
8.1.3 show vlan	35
8.1.4 show lldp neighbors	36
8.1.5 show vrrp brief	37
8.2 VLT validation commands	37
8.2.1 show vlt domain_id	37
8.2.2 show vlt domain_id backup-link	38
8.2.3 show vlt domain_id mismatch	38
9 Deploy VxRail	39
A Validated components for S5148F-ON using VxRail 4.5	41
A.1 Dell EMC PowerSwitches	41
A.2 DAC Cables	41
A.3 VxRail P570 nodes	41
A.4 VxRail Appliance software	42
B VxRail network adapter traffic optimization	43
C VxRail node discovery troubleshooting	44
D Technical resources	45