Dell Vostro 16 5630 Service Manual - Page 37

Power button with optional fingerprint reader

Get Dell Vostro 16 5630 PDF manuals and user guides View all Dell Vostro 16 5630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

4. Replace the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly. 5. Connect the I/O-board cable to the I/O board. 6. Close the latch and replace the clear adhesive tape. 7. Connect the fingerprint-reader cable to the I/O board and close the latch to secure the cable. 8. Align the screw holes on the RJ45 network-port assembly with the screw holes of the I/O board. 9. Replace the three screws (M2x5) that secure the RJ45 network-port assembly to the I/O board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Power button with optional fingerprint reader Removing the power button with optional fingerprint reader Prerequisites CAUTION: The information in this section is intended for authorized service technicians only. 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the I/O board. About this task NOTE: Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer. The following image(s) indicate the location of the power button with optional fingerprint reader and provides a visual representation of the removal procedure. Removing and installing components 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
4.
Replace the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.
5.
Connect the I/O-board cable to the I/O board.
6.
Close the latch and replace the clear adhesive tape.
7.
Connect the fingerprint-reader cable to the I/O board and close the latch to secure the cable.
8.
Align the screw holes on the RJ45 network-port assembly with the screw holes of the I/O board.
9.
Replace the three screws (M2x5) that secure the RJ45 network-port assembly to the I/O board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Power button with optional fingerprint reader
Removing the power button with optional fingerprint reader
Prerequisites
CAUTION:
The information in this section is intended for authorized service technicians only.
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
I/O board
.
About this task
NOTE:
Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer.
The following image(s) indicate the location of the power button with optional fingerprint reader and provides a visual
representation of the removal procedure.
Removing and installing components
37