Dell Vostro 16 5630 Service Manual - Page 45

Trusted Platform Module, Removing the Trusted Platform Module (TPM) board

Get Dell Vostro 16 5630 PDF manuals and user guides View all Dell Vostro 16 5630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

2. Gently place the palm-rest and keyboard assembly under the display hinges. 3. Close the left display hinge and align the screw holes on the left display hinge with the screw holes on the palm-rest and keyboard assembly. 4. Replace the three screws (M2.5x5) that secure the left display hinge to the palm-rest and keyboard assembly. 5. Close the right display hinge and align the screw holes on the right display hinge with the screw holes on the palm-rest and keyboard assembly. 6. Replace the three screws (M2.5x5) that secure the right display hinge to the palm-rest and keyboard assembly. 7. Route the display cable through the routing guides on the palm-rest and keyboard assembly. 8. Connect the display cable to the system board and close the latch. 9. Adhere the tape that secures the display-cable connector latch to the system board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Trusted Platform Module Removing the Trusted Platform Module (TPM) board Prerequisites CAUTION: The information in this section is intended for authorized service technicians only. 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task NOTE: Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer. The following image(s) indicate the location of the tpm board and provides a visual representation of the removal procedure. Removing and installing components 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
2.
Gently place the palm-rest and keyboard assembly under the display hinges.
3.
Close the left display hinge and align the screw holes on the left display hinge with the screw holes on the palm-rest and
keyboard assembly.
4.
Replace the three screws (M2.5x5) that secure the left display hinge to the palm-rest and keyboard assembly.
5.
Close the right display hinge and align the screw holes on the right display hinge with the screw holes on the palm-rest and
keyboard assembly.
6.
Replace the three screws (M2.5x5) that secure the right display hinge to the palm-rest and keyboard assembly.
7.
Route the display cable through the routing guides on the palm-rest and keyboard assembly.
8.
Connect the display cable to the system board and close the latch.
9.
Adhere the tape that secures the display-cable connector latch to the system board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Trusted Platform Module
Removing the Trusted Platform Module (TPM) board
Prerequisites
CAUTION:
The information in this section is intended for authorized service technicians only.
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
About this task
NOTE:
Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer.
The following image(s) indicate the location of the tpm board and provides a visual representation of the removal procedure.
Removing and installing components
45