Dell XPS 15 9570 XPS 15 Service Manual - Page 53

Removing the keyboard, Prerequisites, Procedure, Peeling the Mylar

Page 53 highlights

31 Removing the keyboard WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1 Remove the base cover. 2 Remove the battery (half-length) or the battery (full-length). 3 Remove the memory modules. 4 Follow the procedure from step 1 to step 4 in "Removing the hard drive". 5 Remove the solid-state drive (half-length) or the solid-state drive (full-length). 6 Remove the wireless card. 7 Remove the fans. 8 Remove the heat sink. 9 Remove the system-board assembly. Procedure 1 Peel off the fingerprint reader cable from the palm-rest assembly. 2 Peel off the Mylar that secures the keyboard to the palm-rest assembly. Figure 26. Peeling the Mylar 1 fingerprint-reader cable 2 tape 3 Open the latches and disconnect the keyboard cable and keyboard-backlight cable from the keyboard-controls board. 4 Lift up the Mylar to access the screws that secure the keyboard to the palm-rest assembly. Removing the keyboard 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94

Removing the keyboard
WARNING:
Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After working inside
your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/
regulatory_compliance
.
Prerequisites
1
Remove the
base cover
.
2
Remove the
battery (half-length)
or the
battery (full-length)
.
3
Remove the
memory modules
.
4
Follow the procedure from step 1 to step 4 in “
Removing the hard drive
”.
5
Remove the
solid-state drive (half-length)
or the
solid-state drive (full-length)
.
6
Remove the
wireless card
.
7
Remove the
fans
.
8
Remove the
heat sink
.
9
Remove the
system-board assembly
.
Procedure
1
Peel
off
the
fingerprint
reader cable from the palm-rest assembly.
2
Peel
off
the Mylar that secures the keyboard to the palm-rest assembly.
Figure 26. Peeling the Mylar
1
fingerprint-reader
cable
2
tape
3
Open the latches and disconnect the keyboard cable and keyboard-backlight cable from the keyboard-controls board.
4
Lift up the Mylar to access the screws that secure the keyboard to the palm-rest assembly.
31
Removing the keyboard
53