Dell XPS 15 9570 XPS 15 Service Manual - Page 64

Replacing the display assembly, Procedure, Post-requisites

Get Dell XPS 15 9570 PDF manuals and user guides View all Dell XPS 15 9570 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

38 Replacing the display assembly WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1 Place the palm-rest assembly at the edge of the table with the speakers facing away from the edge. 2 Align the screw holes on the palm-rest assembly with the screw holes on the display hinges. 3 Replace the six screws (M2.5x5) that secure the display assembly to the palm-rest assembly. 4 Turn the computer over and open the display at an angle of 90 degrees. 5 Adhere the tape that secures the touch-screen cable to the system board if applicable. 6 Adhere the tape and connect the touch-screen cable to the system board if applicable. 7 Adhere the tape that secures the display cable to the system board. 8 Route the display cable through the routing guides on the left fan. NOTE: When routing the display cable, make sure that the cable is not routed over the screw hole on the left fan. 9 Replace the screw (M2x2) that secures the display-cable bracket to the system board. Post-requisites 1 Replace the wireless card. 2 Replace the battery (half-length) or the battery (full-length). 3 Replace the base cover. 64 Replacing the display assembly

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Replacing the display assembly
WARNING:
Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After working inside
your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/
regulatory_compliance
.
Procedure
1
Place the palm-rest assembly at the edge of the table with the speakers facing away from the edge.
2
Align the screw holes on the palm-rest assembly with the screw holes on the display hinges.
3
Replace the six screws (M2.5x5) that secure the display assembly to the palm-rest assembly.
4
Turn the computer over and open the display at an angle of 90 degrees.
5
Adhere the tape that secures the touch-screen cable to the system board if applicable.
6
Adhere the tape and connect the touch-screen cable to the system board if applicable.
7
Adhere the tape that secures the display cable to the system board.
8
Route the display cable through the routing guides on the left fan.
NOTE:
When routing the display cable, make sure that the cable is not routed over the screw hole on the left fan.
9
Replace the screw (M2x2) that secures the display-cable bracket to the system board.
Post-requisites
1
Replace the
wireless card
.
2
Replace the
battery (half-length)
or the
battery (full-length)
.
3
Replace the
base cover
.
38
64
Replacing the display assembly