Denon 2310CI Owners Manual - Page 15

Denon 2310CI - AVR AV Receiver Manual

Get Denon 2310CI - AVR AV Receiver PDF manuals and user guides
UPC - 883795000918
View all Denon 2310CI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

ENGLISH Installing/Setting the Speakers Connecting the Speakers Front speakers A Subwoofer with built-in amplifier Front speakers B Center speaker Surround speakers Getting Started s  Set the "Amp Assign" Mode According to the Speaker Layout The signals output from the AVR-2310's SURR. BACK/AMP ASSIGN speaker terminals can be switched to signals of the surround mode being used (vpage 27 "Amp Assign"). Connections Amp assign mode (vpage 27) SURR. BACK/AMP ASSIGN Speaker connections Example of speaker installation (L) (R) (L) (R) (L) (R) w q q w qw q w q w q */ w q w Settings Normal (Default) Surround back speakers (7.1) Playback Normal Surround back speakers b Connect to the "L" speaker terminal. b Set "S.Back" (vpage 28) to "1spkr". Not connected Multi-Zone (6.1) Remote Control Normal Set the "S.Back" setting b (vpage 28) to "None" . (5.1) Information Front Height Front Height speakers (7.1) For connections of the SURR. BACK/AMP ASSIGN speaker terminals, see "Amp Assign" (vpage 27). Troubleshooting Protection circuit If the core wires touch the rear panel and the screws etc., or the ± sides touch each other, the protection circuit will be activated and the power indicator will flash red at intervals of 0.5 secs. If the protection circuit is activated, the speaker output is isolated, and the power supply goes to the standby state. If the power supply is turned off, after the power supply cord is withdrawn, please confirm that speaker cable and input cable are connected. Also, if replaying large sound levels by using a speaker having an impedance less than that specified (eg, 4 Ω/ohms), the temperature will rise, and the protection circuit might be activated. The power supply will go into the standby state, and the power indicator will flash red at 2 second intervals. In this case, please switch off the power supply, and wait until the AVR-2310 has cooled down, and the surrounding ventilation is good. Even if there are no problems with the surrounding ventilation and connections, in the event of the protection circuit becoming activated, due to thinking that the AVR-2310 has failed, please contact DENON Service center after switching off. Front A Bi-Amp or Front B Bi-Amp Front A or B speakers b For connections, see "About bi-amp connections" (vpage 12). (5.1) Specifications ZONE2 ZONE2 speakers MAIN ZONE  ZONE2 (5.1) (2) 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
±±
Getting Started
Playback
Remote Control
Information
Troubleshooting
Specifications
ENGLISH
Multi-Zone
Settings
Protection circuit
If the core wires touch the rear panel and the screws
etc., or the ± sides touch each other, the protection
circuit will be activated and the power indicator will
flash red at intervals of 0.5 secs.
If the protection circuit is activated, the speaker
output is isolated, and the power supply goes to
the standby state. If the power supply is turned off,
after the power supply cord is withdrawn, please
confirm that speaker cable and input cable are
connected.
Also, if replaying large sound levels by using
a speaker having an impedance less than that
specified (eg, 4 Ω/ohms), the temperature will rise,
and the protection circuit might be activated. The
power supply will go into the standby state, and the
power indicator will flash red at 2 second intervals.
In this case, please switch off the power supply,
and wait until the AVR-2310 has cooled down, and
the surrounding ventilation is good.
Even if there are no problems with the surrounding
ventilation and connections, in the event of the
protection circuit becoming activated, due to
thinking that the AVR-2310 has failed, please contact
DENON Service center after switching off.
w
q
w
q
w
q
*/
(L)
(R)
w
q
w
q
(R)
(L)
w
q
w
q
(R)
(L)
Subwoofer with
built-in amplifier
Center
speaker
Surround
speakers
Front speakers
A
Front speakers
B
For connections of the SURR. BACK/AMP
ASSIGN speaker terminals, see “Amp Assign”
(
v
page 27).
Connecting the Speakers
s
Set the “Amp Assign” Mode According to the Speaker Layout
The signals output from the AVR-2310’s SURR. BACK/AMP ASSIGN speaker terminals can be
switched to signals of the surround mode being used (
v
page 27 “Amp Assign”).
Amp assign mode
(
v
page 27)
SURR. BACK/AMP ASSIGN
Speaker connections
Example of speaker installation
Normal
(Default)
Normal
Normal
Front Height
Front A Bi-Amp
or
Front B Bi-Amp
ZONE2
MAIN ZONE
ZONE2
Front Height
speakers
Surround back
speakers
Surround back
speakers
Not connected
Front A or B
speakers
b
For connections, see
“About bi-amp connections”
(
v
page 12).
(7.1)
(6.1)
(5.1)
(7.1)
(5.1)
(5.1)
(2)
b
Connect to the “L” speaker
terminal.
b
Set “S.Back” (
v
page 28)
to “1spkr”.
b
Set the “S.Back” setting
(
v
page 28) to “None”
.
Installing/Setting the Speakers
ZONE2
speakers
Connections