Denon 2310CI Owners Manual - Page 22

Denon 2310CI - AVR AV Receiver Manual

Page 22 highlights

ENGLISH Connecting Devices not Equipped with HDMI terminals Getting Started Connections Settings Playback Multi-Zone Remote Control Information Troubleshooting Specifications External Controller n RS-232C connector When you connect an external control device, you can control the AVR-2310 with the external control device. Perform the operation below beforehand. Connecting the Power Cord n REMOTE CONTROL jacks Infrared retransmitter Infrared sensor Wait until all connections have been completed before connecting the power cord. Power cord (supplied) To household power outlet (AC 230 V, 50 Hz) q Turn on the AVR-2310's power. w  Turn off the AVR-2310's power from the external controller. e Check that the AVR-2310 is in the standby mode. "69 065 Input Output Extension jack for future use. (Connect devices corresponding with room to room function to this jack.) Connection to the AC outlet • This outlet supply power to external audio equipment. • Audio equipment with a total power consumption of 100 W (0.43 A) can be connected. • The power supply turns on and off together with the on the main unit. When set to "ON" , power is supplied from the outlet. When set to "STANDBY" , no power is supplied. NOTE When "HDMI Control" (vpage 30) is set to "ON" , power is supplied constantly to the AC outlet (UNSWITCHED). Set as Necessary Set this to use the RS-232C connector for the DENON RF remote controller. "232C Port" (vpage 33) n TRIGGER OUT jacks NOTE • Insert the AC plugs securely. Incomplete connections could cause noise. • Only use the AC outlet to plug in audio equipment. Do not use them as power supplies for hairdryers or anything other than audio equipment. The TRIGGER OUT output terminal outputs a maximum 12 V/150 mA electrical signal. When a device with TRIGGER IN terminal is connected via a monaural mini-plug, the connected device's power on/standby can be controlled through linked operation to the AVR-2310. When using the AVR-2310 in combination with the DENON RF remote controller (RC-7000CI, sold separately) or RF remote receiver (RC7001RCI, sold separately), two-way communication is enabled. The AVR-2310's status information as well as iPod and Internet audio music files can be browsed watching the RF Remote Controller's display. For details, refer to the operating instructions of the respective devices. Set as Necessary Set to change the conditions for linked operation via the TRIGGER OUT terminal. "Trigger Out" (vpage 33) NOTE On the GUI menu, when setting "232C Port" to "2Way Remote" , you cannot use the RS-232C connector as an external controller (vpage 33). 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80

±8
ENGLISH
Getting Started
Connections
Playback
Remote Control
Information
Troubleshooting
Specifications
Multi-Zone
Settings
Connecting Devices not Equipped with HDMI terminals
Connections
NOTE
• Insert the AC plugs securely. Incomplete connections could cause
noise.
• Only use the AC outlet to plug in audio equipment. Do not use
them as power supplies for hairdryers or anything other than audio
equipment.
Wait until all connections have been completed before connecting the
power cord.
To household
power outlet
(AC 230 V, 50 Hz)
Power cord
(supplied)
Connection to the AC outlet
• This outlet supply power to external audio
equipment.
• Audio equipment with a total power
consumption of 100 W (0.43 A) can be
connected.
• The power supply turns on and off together
with the
on the main unit. When set
to “ON”
, power is supplied from the outlet.
When set to “STANDBY”
, no power is
supplied.
NOTE
When “HDMI Control” (
v
page 30) is set
to “ON”
, power is supplied constantly to
the AC outlet (UNSWITCHED).
Connecting the Power Cord
REMOTE CONTROL jacks
n
"69!
165
TRIGGER OUT jacks
The TRIGGER OUT output terminal outputs a maximum 12
V/150 mA electrical signal. When a device with TRIGGER IN
terminal is connected via a monaural mini-plug, the connected
device’s power on/standby can be controlled through linked
operation to the AVR-2310.
n
Extension jack for future use.
(Connect devices corresponding
with room to room function to
this jack.)
Infrared
retransmitter
Input
Output
Infrared
sensor
External Controller
RS-232C connector
When you connect an external control device, you can control
the AVR-2310 with the external control device. Perform the
operation below beforehand.
q
Turn on the AVR-2310’s power.
w
Turn off the AVR-2310’s power from the external
controller.
e
Check that the AVR-2310 is in the standby mode.
n
When using the AVR-2310 in combination with the DENON RF remote
controller (RC-7000CI, sold separately) or RF remote receiver (RC-
7001RCI, sold separately), two-way communication is enabled. The
AVR-2310’s status information as well as iPod and Internet audio music
files can be browsed watching the RF Remote Controller’s display. For
details, refer to the operating instructions of the respective devices.
Set this to use the RS-232C connector for the DENON RF remote
controller.
“232C Port”
(
v
page 33)
Set as Necessary
NOTE
On the GUI menu, when setting “232C Port” to “2Way Remote”
, you
cannot use the RS-232C connector as an external controller (
v
page
33).
Set to change the conditions for linked operation via the TRIGGER
OUT terminal.
“Trigger Out”
(
v
page 33)
Set as Necessary