Denon 2310CI Owners Manual - Page 37

ENGLISH Making detailed settings (Manual Setup) Setting items Setting contents Setting items Setting contents Getting Started Quick Select Name Rename Label : Change the display name of the selected "Quick Select" Change the Quick Select setting. 1.  Use ui to select the name of the Quick Select setting you want name. to change, then press . 2. Use o p to set the cursor to the character you want to change. 3. Use ui to change the character, then press . • Up to 16 characters can be input. • The input character type can be switched by pressing while the display name is being changed. • The types of characters that can be input are as shown below. GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ GLower case charactersH abcdefghijklmnopqrstuvwxyz GSymbolsH GNumbersH 0123456789 (Space) Trigger Out n When Setting for Zone (MAIN ZONE / ZONE2) Select the condition for Trigger out is activated through linkage to the power of the zone set to activating Trigger Out for "ON". the input source, surround n When Setting for Input Source mode, etc. Activate trigger out when the input source set to "ON" is selected. See "TRIGGER OUT jacks" (vpage 18) for more Valid for the zone set to "ON" with "When Setting for Zone" . information on trigger out. n When Setting for Surround Mode Activate trigger out when the surround mode set to "ON" is selected.  alid when the "MAIN ZONE" set to "ON" with "When Setting V for Zone" is selected, and when the input source set to "ON" with "When Setting for Input Source" is selected. Remote ID 1/2/3/4 Set when you operate When using the AVR-2310 with only the included remote control unit  another DENON AV amplifier (RC-1117), use Remote ID "1" (default). with the remote control unit When using a separately sold remote control unit (RC-7000CI, etc.), of the AVR-2310. Match the this function can be used. Match the ID setting of the remote control remote control unit you are unit and the receiver. using with the remote ID of the AVR-2310. 232C Port Serial Control : Set when using an external controller. Set when using an external 2Way Remote : Set when using a 2-way remote control unit. controller or two-way remote When using a DENON two-way remote control (RC-7000CI or RC control connected to the RS7001RCI, sold separately), set to "2Way Remote" . 232C terminal. Connections Settings Playback  4. Repeat steps 2 and 3 to change the display name. Multi-Zone Zone Rename 1.  Use ui to select the zone name you want to change, then press Rename the display names . of the different zones as MAIN ZONE / ZONE2 desired. 2. Use o p to set the cursor to the character you want to change. 3. Use ui to change the character, then press . • Up to 10 characters can be input. • The input character type can be switched by pressing while the display name is being changed. • The types of characters that can be input are as shown below. GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ GLower case charactersH abcdefghijklmnopqrstuvwxyz GSymbolsH GNumbersH 0123456789 (Space) 4. Repeat steps 2 and 3 to change the display name. Remote Control Information NOTE When setting to "2Way Remote" , you can not use the RS-232C connector as an external controller. Dimmer Bright : Normal display brightness. Adjust display brightness of Dim : Reduced display brightness. the receiver. Dark : Very low display brightness. OFF : Turns the display off. Setup Lock Protect settings inadvertent change.  Switching is also possible by pressing ON : Turn protection on. from OFF : Turn protection off. on the main unit. Troubleshooting Specifications  When "Setup Lock" is set to "ON" , the settings listed below can no longer be changed. Also, "SETUP LOCKED!" is displayed if you attempt to operate related settings. ・RESTORER ・Dynamic Volume ・MultEQ ・Channel Level ・Dynamic EQ ・Audio Delay Remote control operation buttons Displaying the menu : Cancel the menu : Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menu 33