Denon S-5BD Owners Manual - English - Page 11
Preparation, Speaker Detection, Measurement - problems
UPC - 083795001216
View all Denon S-5BD manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
Getting Started Simple Version Connections Playback (Basic) Settings Playback (Advanced) ENGLISH Set Up Speakers (Audyssey™ Auto Setup) 2 Set Up the Subwoofer If using a subwoofer capable of the following adjustments, set up the subwoofer as shown below. n When using a subwoofer with a direct mode Set the direct mode to "On" and disable the volume adjustment and crossover frequency setting. n When using a subwoofer without a direct mode Make the following settings: • Volume : "12 o'clock position" • Crossover frequency : "Maximum/Highest Frequency" • Low pass filter : "Off" • Standby mode : "Off" 3 Connect the setup microphone to the SETUP MIC jack of this unit. n If "Cancel" is Selected "Cancel setup?" is displayed on the GUI screen. If "Yes" is selected, "FIRST SETUP" closes. • Setting up the speakers again Repeat the operation from step 3 of STEP1 Preparation . The title of the GUI screen will change from "FIRST SETUP" to "AUDYSSEY AUTO SETUP" at this point, but the operation method is the same. STEP 1 Preparation FIRST SETUP 2/2 STEP1 Preparation Please connect the include calibrated setup microphone Enter It prepares for beginning an auto setup. RETURN Cancel When the setup microphone is connected, the following screen is displayed. FIRST SETUP 2/2 STEP1 Preparation 1 2 3 4 5 6 In a typical setup, select "Auto Setup Start". When connecting speakers in a setup other than 2ch/2.1ch/5.1ch, select "Speaker Assign". Speaker Assign Auto Setup Start Start Auto Setup Enter RETURN Cancel When setting up speakers other than 5.1-channel speakers, select "Speaker Assign". When the "Speaker Assign" setup screen appears, perform the operations in Step 2 and 3 of "Set Up Speakers" (vpage 36). 4 Select "Auto Setup Start" and then press ENTER. STEP 2 Speaker Detection STEP 3 Measurement 5 Select "Measure" and then press ENTER. When measuring begins, a test tone is output from each speaker. When measuring ends, the speaker detection results are displayed. FIRST SETUP 2/2 STEP2 Speaker Detection Please place the microphone at ear height at main listening position. 1 2 3 4 5 6 7 Move the setup microphone to position 2, select "Measure", and then press ENTER. The measurement of the second position starts. Measurements can be made in up to six positions. FIRST SETUP 2/2 STEP3 Measurement 1 2 3 4 5 6 Please place the microphone at ear height at 2nd listening position (up to 6 position). Measure Enter RETURN Cancel Start measurement. Output large test tone during measuring 6 Select "Next → Measurement" and then press ENTER. NOTE If "Caution!" is displayed: Go to "Error Messages" (vpage 9), check any related items, and perform the necessary procedures. If the problem is resolved, return and restart "Audyssey Auto Setup". n When Performing Audyssey Auto Setup Over Again Press ui to select "Retry", and then press ENTER. n When Measuring has Stopped Press RETURN, and the "Cancel setup?" prompt is displayed. Press o p and select "Yes", then press ENTER. Measure Next Calculation Enter RETURN Cancel Start measurment. Output large test tone during measuring 8 Repeat step 7, measuring positions 3 to 6. When measurement of position 6 is completed, a "Measurements finished." message is displayed. FIRST SETUP 2/2 STEP3 Measurement 1 2 3 4 5 6 Please place the microphone at ear height at 3rd listening position (up to 6 position). Measure Retry Next Calculation Enter RETURN Cancel Start measurment. Output large test tone during measuring If you want to omit measurements from the next point onward, select "Next Calculation". (Go to vpage 8 STEP4 Calculation ) Multizone GUI Remote Control Part Names Other Information Troubleshooting Spec. Index Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu