Edimax EW-7228APn Manual - Page 61

WPS/Reset, III-7-3., DHCP Server - factory reset

Get Edimax EW-7228APn PDF manuals and user guides View all Edimax EW-7228APn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Note: To reset the IP address back to its default value of 192.168.2.1, press and hold the WPS/Reset button on the access point for 10 seconds. Be aware that doing so restores all settings and passwords back to factory defaults. Click "APPLY" to save changes. The following message will appear: Click "CONTINUE" to save the changes but not apply them yet. This allows you to make further changes in the browser-based management interface, before applying them all at once. Click "APPLY" to restart the device and implement any changes. The device will restart itself. III-7-3. DHCP Server The access point can be configured to act as a DHCP server for your network. By default DHCP is disabled. Note: This option will be unavailable unless you enable this function by selecting "Enabled" from the drop down menu labeled "DHCP Server", under the heading "Management IP" as detailed above Enter the appropriate information as shown below. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
61
Note
: To reset the IP address back to its
default value of 192.168.2.1, press and hold
the
WPS/Reset
button on the access point
for 10 seconds. Be aware that doing so
restores
all
settings and passwords back to
factory defaults.
Click
“
APPLY
”
to save changes. The following message will appear:
Click
“
CONTINUE
”
to save the changes but not apply them yet. This allows you
to make further changes in the browser-based management interface, before
applying them all at once.
Click
“
APPLY
”
to restart the device and implement any changes. The device will
restart itself.
III-7-3.
DHCP Server
The access point can be configured to act as a DHCP server for your network.
By default DHCP is disabled.
Note
: This option will be unavailable unless
you enable this function by selecting
“
Enabled
”
from the drop down menu
labeled
“
DHCP Server
”
, under the heading
“
Management IP
”
as detailed above
Enter the appropriate information as shown below.