Epson LX-300II Product Information Guide - Page 14
Default Settings - printer driver
View all Epson LX-300II manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
Epson LX-300+II Default Settings While you can often set the default settings through your application software or printer driver, you may need to change a default setting from the printer's control panel using Default setting mode. The table below lists the default settings (in bold) and options you can select in this mode. (For more information, see the Reference Guide.) ) Settings Page length for tractor Skip over perforation Auto tear-off Auto line feed Print direction Software 0 slash High speed draft I/F (interface) mode Auto I/F wait time Baud rate (bps) Parity Data length Parallel I/F bidirectional mode Packet mode Character table* Options Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5, 11, 70/6, 12, 14, 17 On, Off On, Off On, Off Bi-D, Uni-D ESC/P, IBM 2380 Plus On, Off On, Off Auto, Parallel, Serial 10 seconds, 30 seconds 19200, 9600, 4800, 2400, 1200, 600, 300 None, Odd, Even, Ignore 7 bit, 8 bit On, Off Auto, Off Standard model: Italic, PC 437, PC 850, PC 860, PC 863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, ISO 8859-15 International character set for Italic table Manual feed wait time Buzzer Auto CR (IBM 2380 Plus)* IBM character table* All other models: Italic, PC 437, PC 850, PC 437 Greek, PC 853, PC 855, PC 852, PC 857, PC 866, PC 869, MAZOWIA, Code MJK, ISO 8859-7, ISO Latin 1T, Bulgaria, PC 774, Estonia, ISO 8859-2, PC 866 LAT, PC 866 UKR, PC APTEC, PC 708, PC 720, PC AR864, PC 860, PC 863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, ISO 8859-15, PC 771, PC437 Slovenia, PC MC, PC1250, PC1251 Italic U.S.A., Italic France, Italic Germany, Italic U.K., Italic Denmark1, Italic Sweden, Italic Italy, Italic Spain1 1 second, 1.5 seconds, 2 seconds, 3 seconds On, Off On, Off Table 1, Table 2 * These settings take effect only when IBM 2380 Plus emulation is selected. Changing Default Settings Follow the steps below to enter Default Setting mode. If you use single sheets, you'll need to load a new sheet of paper each time the printer ejects a printed page. 1. Make sure paper is loaded and the printer is off. 2. Hold down the Tear Off (Font) button and then turn on the printer. The printer enters Default Setting mode and prints instructions for selecting the language. The current language is indicated by which control panel lights are on. (For English, only the Pause light is on.) 3. If you want a different language, press the LF/FF button until the lights show the language you want. 4. Press the Tear Off (Font) button to print a list of all the current settings. 5. If the settings are all correct, turn off the printer to exit Default Setting mode. If you want to change any settings, go to step 6. 6. Press the Tear Off (Font) button. The printer prints instructions for changing the settings. 7. Press the LF/FF button to scroll through the options for the selected setting until you see the one you want. Then press the Tear Off (Font) button to select the next setting you want to change. 8. When you finish making settings, turn off the printer to exit Default Setting mode. Your new settings remain in effect until you change them again or reset the printer's defaults. Restoring the printer's default settings If you want to restore all the factory default settings, turn off the printer. Then hold down the Load/Eject, LF/FF, and Pause buttons while you turn on the printer. 14 - Epson LX-300+II 7/06