Epson LX-300II Product Information Guide - Page 5

Control Panel Buttons and Lights - paper

Page 5 highlights

Epson LX-300+II Roll paper A B Printable area A The minimum top margin is 0.17 inch (4.2 mm). B The minimum left and right margins are 0.12 inch (3 mm). The maximum printable width is 8 inches (203.2 mm). Control Panel Buttons and Lights 1 Tear Off (Font) lights Flash when continuous paper is in the tear-off position; otherwise, the lights indicate the selected font. 2 Tear Off (Font) button ❏ Advances continuous paper to the tear-off position. ❏ Feeds continuous paper backward from the tear-off position to the top-of-form position. ❏ In Micro Adjust mode, selects one of the six built-in fonts. 3 LF/FF button ❏ Feeds paper line by line when pressed and released. ❏ Ejects a single sheet or advances continuous paper to the next top-of-form position when held down. ❏ In Micro Adjust mode, adjusts the top-of-form and tear-off position. 4 Load/Eject button ❏ Loads a single sheet of paper. ❏ Ejects a single sheet of paper. ❏ Loads continuous paper from the standby position. ❏ Feeds continuous paper backward to the standby position. ❏ In Micro Adjust mode, adjusts the top-of-form and tear-off positions. 5 Pause button Stops printing temporarily, and resumes printing when pressed again. When held down for three seconds, turns on Micro Adjust mode. To turn it off, press it again. 6 Paper Out light ❏ On when no paper is loaded in the selected paper source or when paper is not loaded correctly. ❏ Flashes when paper has not been fully ejected or if paper is jammed in the printer. 7 Pause light ❏ On when the printer is paused. ❏ Flashes when the printer is in Micro Adjust mode. ❏ Flashes when the print head has overheated. Selecting a Built-in Font It is best to use your application program to select the font you want to use in a document. However, you may sometimes need to select one of the printer's six built-in fonts using the buttons on the control panel, as described below. (The settings you make in application programs usually override settings you make from the printer's control panel.) ❏ Draft ❏ Roman ❏ Sans Serif ❏ Draft Condensed ❏ Roman Condensed ❏ Sans Serif Condensed 7/06 Epson LX-300+II - 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

Epson LX-300+II
7/06
Epson LX-300+II
-
5
Roll paper
A The minimum top margin is 0.17 inch (4.2 mm).
B The minimum left and right margins are 0.12 inch (3 mm).
The maximum printable width is 8 inches (203.2 mm).
Control Panel Buttons and Lights
1
Tear Off (Font) lights
Flash when continuous paper is in the tear-off position;
otherwise, the lights indicate the selected font.
2
Tear Off (Font) button
Advances continuous paper to the tear-off position.
Feeds continuous paper backward from the tear-off position
to the top-of-form position.
In Micro Adjust mode, selects one of the six built-in fonts.
3
LF/FF button
Feeds paper line by line when pressed and released.
Ejects a single sheet or advances continuous paper to the
next top-of-form position when held down.
In Micro Adjust mode, adjusts the top-of-form and tear-off
position.
4
Load/Eject button
Loads a single sheet of paper.
Ejects a single sheet of paper.
Loads continuous paper from the standby position.
Feeds continuous paper backward to the standby position.
In Micro Adjust mode, adjusts the top-of-form and tear-off
positions.
5
Pause button
Stops printing temporarily, and resumes printing when pressed
again. When held down for three seconds, turns on Micro
Adjust mode. To turn it off, press it again.
6
Paper Out light
On when no paper is loaded in the selected paper source or
when paper is not loaded correctly.
Flashes when paper has not been fully ejected or if paper is
jammed in the printer.
7
Pause light
On when the printer is paused.
Flashes when the printer is in Micro Adjust mode.
Flashes when the print head has overheated.
Selecting a Built-in Font
It is best to use your application program to select the font you
want to use in a document. However, you may sometimes need
to select one of the printer’s six built-in fonts using the buttons
on the control panel, as described below. (The settings you
make in application programs usually override settings you
make from the printer’s control panel.)
B
A
Printable
area
Draft
Draft Condensed
Roman
Roman Condensed
Sans Serif
Sans Serif Condensed