Epson P3000 User Manual - Page 17

Other equipment that emits infrared energy, such as a radiant room heater, Remote control information - battery

Get Epson P3000 - Digital AV Player PDF manuals and user guides
UPC - 010343860476
View all Epson P3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Remote control information The ELP-3000 allows you operate it by remote control bia infrared(IR) receivers located at the front and back of projector. The projector may not respond to remote control commands under the following conditions : l The ambient room light is too bright l Certain types of fluorescent lighting are used l A strong light sourse shines into either IR receiver l Other equipment that emits infrared energy, such as a radiant room heater, is in the room. These conditions commonly cause problems for most infrared-controlled equipment. Try the following solutions : l The remote control unit's batteries may be low on power, replace the batteries. l Dim the ambient lighting and/or Dim off any fluorescent lights. l Close any window coverings and/or move the projector out of direct sunlight. l Turn off other equipment that emits infrared energy. If the remote control still does not work properly, cover the unused IR receiver on the projector with light-blocking material, such as masking tape. Remember, you can always control your computer-based presentation directly from the computer, even in an environment containing one of the conditions listed above. README File Information The diskettes that came with your projector include README files that contain additional important information about the projector. Be sure to read these files. xvi introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Remote control information
The ELP-3000 allows you operate it by remote control bia infrared(IR) receivers
located at the front and back of projector. The projector may not respond to
remote control commands under the following conditions :
l
The ambient room light is too bright
l
Certain types of fluorescent lighting are used
l
A strong light sourse shines into either IR receiver
l
Other equipment that emits infrared energy, such as a radiant room heater,
is in the room.
These conditions commonly cause problems for most infrared-controlled
equipment.
Try the following solutions :
l
The remote control unit’s batteries may be low on power, replace the batteries.
l
Dim the ambient lighting and/or Dim off any fluorescent lights.
l
Close any window coverings and/or move the projector out of direct sunlight.
l
Turn off other equipment that emits infrared energy.
If the remote control still does not work properly, cover the unused IR receiver
on the projector with light-blocking material, such as masking tape.
Remember, you can always control your computer-based presentation directly
from the computer, even in an environment containing one of the conditions
listed above.
README File Information
The diskettes that came with your projector include README files that contain
additional important information about the projector. Be sure to read these
files.
xvi
introduction