Epson TM-m30II Technical Reference Guide TM-m30II-N - Page 114

Notes on using the Wireless LAN unit, Notes on Wi-Fi connection, Notes on use, Initial settings

Get Epson TM-m30II PDF manuals and user guides View all Epson TM-m30II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 114 highlights

Appendix Initial settings These settings apply when the printer is initialized in the Interface Setup mode. Parameter Setting value Communication standard Network mode SSID 802.11b/g/n Infrastructure mode EPSON_Printer Encryption type Passphrase IP Address WPA2-Personal EpsonNet Automatically acquired by DHCP ∗ You can connect to a WPA2-PSK (AES) access point using the settings above. Settings in SimpleAP mode (Factory default settings) Parameter Setting value SSID EPSON_Printer Passphrase 12345678 IP Address 192.168.192.168 Subnet mask 255.255.255.0 ∗ In SimpleAP mode, DHCP Server is working and assign IP address to host automatically. Notes on using the Wireless LAN unit • Keep the printer away from the devices, such as kitchen microwaves, that may cause radio wave interference. • Use channels that are away from the frequency bands that may cause radio wave interference. • Place shields between the printer and the devices that may cause radio wave interference. • Select either 2.4 GHz or 5 GHz, whichever is free from radio wave interference. • In auto channel setting for the access point, do not select a channel in which the printer may cause radio wave interference. Notes on Wi-Fi connection Because not all the combinations of the printer and Wireless LAN units have been checked for operation, the operation of the printer in combination with all the Wireless LAN units is not guaranteed. Especially in the adhoc mode, the printer may not operate normally, depending on the combination of the device to connect with. Be sure to carry out evaluation of the operation before use. Notes on use • When you initialize or change the printer settings, the printer is reset to reflect the settings. It may take about 1 minute depending on the network settings or environment. Also, your application may indicate power off during the time waiting for reset. In that case, wait for about 1 minute, and then reconnect to the printer. • Where Wi-Fi communication is in heavy traffic, your application may falsely recognize that the communication is disconnected and indicate power off due to response delay. In that case, disable Power Save to improve the trouble. 114

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
114
Appendix
Initial settings
These settings apply when the printer is initialized in the Interface Setup mode.
∗
You can connect to a WPA2-PSK (AES) access point using the settings above.
Settings in SimpleAP mode (Factory default settings)
∗
In SimpleAP mode, DHCP Server is working and assign IP address to host automatically.
Notes on using the Wireless LAN unit
•
Keep the printer away from the devices, such as kitchen microwaves, that may cause radio wave interference.
•
Use channels that are away from the frequency bands that may cause radio wave interference.
•
Place shields between the printer and the devices that may cause radio wave interference.
•
Select either 2.4 GHz or 5 GHz, whichever is free from radio wave interference.
•
In auto channel setting for the access point, do not select a channel in which the printer may cause radio
wave interference.
Notes on Wi-Fi connection
Because not all the combinations of the printer and Wireless LAN units have been checked for operation, the
operation of the printer in combination with all the Wireless LAN units is not guaranteed. Especially in the ad-
hoc mode, the printer may not operate normally, depending on the combination of the device to connect with.
Be sure to carry out evaluation of the operation before use.
Notes on use
•
When you initialize or change the printer settings, the printer is reset to reflect the settings. It may take about
1 minute depending on the network settings or environment. Also, your application may indicate power off
during the time waiting for reset. In that case, wait for about 1 minute, and then reconnect to the printer.
•
Where Wi-Fi communication is in heavy traffic, your application may falsely recognize that the
communication is disconnected and indicate power off due to response delay. In that case, disable Power
Save to improve the trouble.
Parameter
Setting value
Communication standard
802.11b/g/n
Network mode
Infrastructure mode
SSID
EPSON_Printer
Encryption type
WPA2-Personal
Passphrase
EpsonNet
IP Address
Automatically acquired by DHCP
Parameter
Setting value
SSID
EPSON_Printer
Passphrase
12345678
IP Address
192.168.192.168
Subnet mask
255.255.255.0