Epson TM-m30II Technical Reference Guide TM-m30II-N - Page 21

Power, Error, Paper, Wi-Fi, Ethernet, Printer Status, Software Settings

Get Epson TM-m30II PDF manuals and user guides View all Epson TM-m30II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Chapter 1 Product Overview Power LED Error LED Paper LED Wi-Fi LED Ethernet Bluetooth LED LED Printer Status N F - O O F O O O O F O F O O F *4 N O O O F *5 O O O O O Unrecoverable Errors CAUTION: Turn off the power immediately when an unrecoverable error occurs. If the same error occurs again even after turning the power back on, contact qualified service personnel. O Updating firmware O While forced updating firmware mode is on O During turn-off process O During power off NOTE: The printer enters this status while processing the power off command. It is recommended to use this method when you need to save information on the printer's operating status if the power is cut without using the power switch. *1: To detect this status (remaining amount of roll paper is low), enable the "Roll paper near-end detection" function. For more details, see "Software Settings" on page 48. This function can be used only with a 80-mm width roll paper and only when the printer has been set up to eject printed paper from the front side. For more details about the restrictions, see "Enabling the Roll Paper Near-End Detection" on page 47. *2: The Error LED flashing pattern is: turning on and off alternately at 320 ms intervals for five seconds, then goes off. *3: The Power LED flashing pattern is: lighting for 160 ms followed by a pause for 4960 ms. *4: The Power LED flashing pattern is: lighting for 320 ms followed by a pause for 320 ms. *5: The Power LED flashing pattern is: lighting for 160 ms followed by a pause for 2400 ms. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
21
Chapter 1
Product Overview
*1: To detect this status (remaining amount of roll paper is low), enable the "Roll paper near-end detection"
function. For more details, see
"Software Settings" on page 48
. This function can be used only with a 80-mm
width roll paper and only when the printer has been set up to eject printed paper from the front side. For more
details about the restrictions, see
"Enabling the Roll Paper Near-End Detection" on page 47
.
*2: The Error LED flashing pattern is: turning on and off alternately at 320 ms intervals for five seconds, then
goes off.
*3: The Power LED flashing pattern is: lighting for 160 ms followed by a pause for 4960 ms.
*4: The Power LED flashing pattern is: lighting for 320 ms followed by a pause for 320 ms.
*5: The Power LED flashing pattern is: lighting for 160 ms followed by a pause for 2400 ms.
N
F
-
O
O
O
Unrecoverable Errors
CAUTION:
Turn off the power immediately when
an unrecoverable error occurs.
If the same error occurs again even after
turning the power back on, contact
qualified service personnel.
F
O
O
O
O
O
Updating firmware
F
O
F
O
O
O
While forced updating firmware mode is
on
F
*4
N
O
O
O
O
During turn-off process
F
*5
O
O
O
O
O
During power off
NOTE:
The printer enters this status while
processing the power off command. It is
recommended to use this method
when you need to save information on
the printer’s operating status if the
power is cut without using the power
switch.
Power
LED
Error
LED
Paper
LED
Wi-Fi
LED
Ethernet
LED
Bluetooth
LED
Printer Status