Epson TM-m30II Technical Reference Guide TM-m30II-N - Page 52

Interface selection, Column emulation mode, Command execution during offline

Get Epson TM-m30II PDF manuals and user guides View all Epson TM-m30II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Chapter 3 Advanced Usage Interface selection • Standard USB only • Ethernet/Wi-Fi only • USB-A - Device Charging only • Enable all the interfaces (initial setting) Column emulation mode • 48/35 characters mode (standard mode) (initial setting) • 42/32 characters mode Command execution during offline • Enabled (initial settings) • Disabled Amount of top margin by backfeed • 2.0mm • 9.5mm (no backfeed) (initial settings) • When using the backfeed function with the printer that has been set up to eject paper from the top side, remove any paper ejected from the ejection slot before starting printing. • Disable the automatic top logo setting when enabling backfeed. • Even if the "backfeed" has been enabled, it is not performed during the self-test. • If setting a top margin of 5 mm {0.2"} or less, confirm that no errors occur in your environment of usage. Usage in a hot and humid environment or usage of paper that curls easily may increase the risk of paper jams. • When the paper is fed backward, the paper may get wrinkled or smeared due to a slack in the roll. It is recommended to use thermal paper that has high resistance to abrasion. • Make sure to feed the paper by at least 20 mm before moving the auto cutter. It the paper feed length is not enough, it may cause a paper jam. You can specify values in 0.5mm steps if you use TM-m30II Utility or TM Utility for iOS/Android. Interface switch waiting time Select from 1 to 10 seconds (in intervals of 1 second) 1 second (initial setting) 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
52
Chapter 3
Advanced Usage
Interface selection
•
Standard USB only
•
Ethernet/Wi-Fi only
•
USB-A - Device Charging only
•
Enable all the interfaces (initial setting)
Column emulation mode
•
48/35 characters mode (standard mode) (initial setting)
•
42/32 characters mode
Command execution during offline
•
Enabled (initial settings)
•
Disabled
Amount of top margin by backfeed
•
2.0mm
•
9.5mm (no backfeed) (initial settings)
Interface switch waiting time
Select from 1 to 10 seconds (in intervals of 1 second)
1 second (initial setting)
•
When using the backfeed function with the printer that has been set up to eject paper from the
top side, remove any paper ejected from the ejection slot before starting printing.
•
Disable the automatic top logo setting when enabling backfeed.
•
Even if the "backfeed" has been enabled, it is not performed during the self-test.
•
If setting a top margin of 5 mm {0.2"} or less, confirm that no errors occur in your environment of
usage. Usage in a hot and humid environment or usage of paper that curls easily may increase
the risk of paper jams.
•
When the paper is fed backward, the paper may get wrinkled or smeared due to a slack in the
roll. It is recommended to use thermal paper that has high resistance to abrasion.
•
Make sure to feed the paper by at least 20 mm before moving the auto cutter. It the paper feed
length is not enough, it may cause a paper jam.
You can specify values in 0.5mm steps if you use TM-m30II Utility or TM Utility for iOS/Android.