Esoteric G-02X Owners Manual EN FR SP - Page 17

Messages, Maintenance, For safety, disconnect the power plug from the, outlet before cleaning.

Get Esoteric G-02X PDF manuals and user guides View all Esoteric G-02X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Messages Maintenance PLL LCKING The 10 MHz reference clock from the built-in crystal oscillator (OCXO) or the reference frequency input (EXT IN) connector is being locked by the internal PLL circuit. When locking completes, this message will disappear. oo Ordinarily, only a few seconds are needed until locking completes (PLL locking time), but it can take up to a minute depending on the operating temperature and other factors. oo If locking cannot be completed because input conditions are not met when set to EXT10M, the message will continue to be displayed. Check the input reference clock specifications. Use a soft dry cloth to wipe the surface of the unit clean. For stubborn smudges, use a damp cloth that has been thoroughly wrung out to remove excess moisture. VVFor safety, disconnect the power plug from the outlet before cleaning. oo Never spray liquid directly on this unit. oo Do not use chemically-treated wipes, thinner or similar substances because they could damage the surface of the unit. oo Avoid allowing rubber or plastic materials to touch the unit for long periods of time because they could damage the cabinet. NO 10M-IN! This appears when the reference clock is set to EXT10M and no 10MHz reference clock signal is being input to the reference frequency input (EXT IN) connector. Check the input reference clock. When not using an external clock source, set it to OCXO (page 16). English 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
17
English
Messages
PLL LCKING
The 10 MHz reference clock from the built-in crystal oscillator
(OCXO) or the reference frequency input (EXT IN) connector is
being locked by the internal PLL circuit.
When locking completes, this message will disappear.
o
Ordinarily, only a few seconds are needed until locking com-
pletes (PLL locking time), but it can take up to a minute
depending on the operating temperature and other factors.
o
If locking cannot be completed because input conditions are
not met when set to EXT10M, the message will continue to be
displayed.
Check the input reference clock specifications.
NO 10M-IN!
This appears when the reference clock is set to EXT10M and no
10MHz reference clock signal is being input to the reference fre-
quency input (EXT IN) connector.
Check the input reference clock.
When not using an external clock source, set it to OCXO (page
16).
Maintenance
Use a soft dry cloth to wipe the surface of the unit clean.
For stubborn smudges, use a damp cloth that has been thoroughly
wrung out to remove excess moisture.
V
For safety, disconnect the power plug from the
outlet before cleaning.
o
Never spray liquid directly on this unit.
o
Do not use chemically-treated wipes, thinner or similar substances
because they could damage the surface of the unit.
o
Avoid allowing rubber or plastic materials to touch the unit for
long periods of time because they could damage the cabinet.