Gateway E-9422R Gateway E-9422R Server User Guide - Page 21

Removing the server from a cabinet, Starting your server

Get Gateway E-9422R PDF manuals and user guides View all Gateway E-9422R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

www.gateway.com 3 Remove the bezel lock keys from the inside of the bezel, then insert the left side of the bezel into the left handle and swing the right side of the bezel in until it snaps into place. 4 When the bezel is in place, lock the bezel by inserting the key into the lock in the lower right corner of the bezel and turning it clockwise until it stops. 5 Put the key in a safe place. Removing the server from a cabinet Warning Screws are required to support the front of the server. You must support the server while removing the front screws and while sliding the server off the cabinet rails. If the server is not supported, damage to the server or injury may result. To remove the server from a cabinet: 1 Remove the mounting screws through the handles that hold the server in the cabinet. 2 While supporting the server, slide the server out from the cabinet. Starting your server Caution When you connect peripheral devices to the server, make sure that your server and devices are turned off and the power cords are unplugged. Before you start your server for the first time: • Make sure that the server and monitor are plugged into a power outlet or surge protector and that the surge protector (if you are using one) is turned on. • Make sure that all cables are connected securely to the correct ports and jacks on the back of the server. To start the server: 1 Turn on any peripheral devices connected to the server. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
www.gateway.com
15
3
Remove the bezel lock keys from the inside of the bezel, then insert the left side of the bezel
into the left handle and swing the right side of the bezel in until it snaps into place.
4
When the bezel is in place, lock the bezel by inserting the key into the lock in the lower
right corner of the bezel and turning it clockwise until it stops.
5
Put the key in a safe place.
Removing the server from a cabinet
To remove the server from a cabinet:
1
Remove the mounting screws through the handles that hold the server in the cabinet.
2
While supporting the server, slide the server out from the cabinet.
Starting your server
Before you start your server for the first time:
•
Make sure that the server and monitor are plugged into a power outlet or surge protector
and that the surge protector (if you are using one) is turned on.
•
Make sure that all cables are connected securely to the correct ports and jacks on the back
of the server.
To start the server:
1
Turn on any peripheral devices connected to the server.
Warning
Screws are required to support the front of the server. You must support the server
while removing the front screws and while sliding the server off the cabinet rails. If the
server is not supported, damage to the server or injury may result.
Caution
When you connect peripheral devices to the server, make sure that your server and
devices are turned off and the power cords are unplugged.