Gateway E-9422R Gateway E-9422R Server User Guide - Page 47

Close the lock to hold the card in place, then replace the screw that holds the lock closed.

Get Gateway E-9422R PDF manuals and user guides View all Gateway E-9422R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

www.gateway.com 7 If you are replacing the riser card, continue with the next step. - OR If you are replacing the PCI card, go to Step 10. 8 Press the retaining clip (7) holding the riser card in the riser card assembly, then push the riser card in the direction shown to unlock and remove it. 9 Insert the new riser card into the riser card assembly, then push it toward the back of the assembly. It should snap into place. If you are installing a new PCI card, go to the next step, otherwise go to Step 12. 10 Insert the new PCI card into the riser card, making sure any connectors extend through the slot at the back of the assembly and that the card is fully seated in the riser card. 11 Close the lock to hold the card in place, then replace the screw that holds the lock closed. 12 Position the PCI riser assembly over the PCI sockets on the server board, then press the PCI riser assembly into the PCI sockets. 13 Follow the instructions in "Closing the server case" on page 30. 14 See the card's documentation for software installation instructions. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
www.gateway.com
41
7
If you are replacing the riser card, continue with the next step.
- OR -
If you are replacing the PCI card, go to
Step 10
.
8
Press the retaining clip (7) holding the riser card in the riser card assembly, then push the
riser card in the direction shown to unlock and remove it.
9
Insert the new riser card into the riser card assembly, then push it toward the back of the
assembly. It should snap into place. If you are installing a new PCI card, go to the next step,
otherwise go to
Step 12.
10
Insert the new PCI card into the riser card, making sure any connectors extend through the
slot at the back of the assembly and that the card is fully seated in the riser card.
11
Close the lock to hold the card in place, then replace the screw that holds the lock closed.
12
Position the PCI riser assembly over the PCI sockets on the server board, then press the PCI
riser assembly into the PCI sockets.
13
Follow the instructions in
“Closing the server case” on page 30
.
14
See the card’s documentation for software installation instructions.