Gateway E-9422R Gateway E-9422R Server User Guide - Page 56

Replacing the ROMB battery pack for mezzanine RAID card

Get Gateway E-9422R PDF manuals and user guides View all Gateway E-9422R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

CHAPTER 4: Installing Components Replacing the ROMB battery pack for mezzanine RAID card Warning Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of or recycle used batteries by taking them to a hazardous waste facility. Follow all local regulations for correct battery disposal. To replace the ROMB battery pack for mezzanine RAID card: 1 Follow the instructions in "Preventing static electricity discharge" on page 28. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server. 2 Follow the instructions in "Opening the server case" on page 29. 3 Press the release handle (1), then slide the ROMB battery pack for mezzanine RAID card (2) toward the back of the chassis to release it from the locking tabs and lift it out of the chassis (3). 4 Align the holes in the bottom of the new ROMB battery pack for mezzanine RAID card (1) with the locking tabs in the chassis, then press it into place in the chassis. 5 Slide the ROMB battery pack for mezzanine RAID card (2) toward the front of the chassis until it clicks into place. 6 Follow the instructions in "Closing the server case" on page 30. 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
CHAPTER 4: Installing Components
50
Replacing the ROMB battery pack for mezzanine
RAID card
To replace the ROMB battery pack for mezzanine RAID card:
1
Follow the instructions in
“Preventing static electricity discharge” on page 28
. Make sure
that you turn off the server, then unplug the power cord(s) and all other cables connected
to the server.
2
Follow the instructions in
“Opening the server case” on page 29
.
3
Press the release handle (1), then slide the ROMB battery pack for mezzanine RAID card (2)
toward the back of the chassis to release it from the locking tabs and lift it out of the
chassis (3).
4
Align the holes in the bottom of the new ROMB battery pack for mezzanine RAID card (1)
with the locking tabs in the chassis, then press it into place in the chassis.
5
Slide the ROMB battery pack for mezzanine RAID card (2) toward the front of the chassis
until it clicks into place.
6
Follow the instructions in
“Closing the server case” on page 30
.
Warning
Danger of explosion if the battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of or recycle used batteries
by taking them to a hazardous waste facility. Follow all local regulations for correct battery
disposal.