Gateway E-9422R Gateway E-9422R Server User Guide - Page 53

Replacing the power cage

Get Gateway E-9422R PDF manuals and user guides View all Gateway E-9422R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

www.gateway.com 4 Pull the power supply module straight out of the server with the handle. It may take considerable force to remove. 5 Push the new power supply module into the server, with the retaining clip on the right, until it locks into place. 6 Reconnect the AC power cord for the new power supply module. Replacing the power cage To replace the power cage: 1 Follow the instructions in "Preventing static electricity discharge" on page 28. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server. 2 Follow the instructions in "Opening the server case" on page 29. 3 Remove the power supply modules by following the instructions in "Replacing a power supply module" on page 46. 4 Disconnect the main power, CPU power, and power signal cables from the system board. See "System board" on page 4 for the location of the connectors on the system board. 5 Remove the screws (3) holding the power cage in the chassis. 6 Slide the power cage (4) toward the front of the chassis to disengage the locking tabs, then lift the power cage out of the chassis. 7 Place the new power cage into the chassis, aligning the cage with the locking tabs in the chassis, then slide the power cage toward the back of the chassis to engage the locking tabs. 8 Replace the screws you previously removed, then connect the cables to the system board. 9 Reinstall the power supply modules by following the instructions in "Replacing a power supply module" on page 46. 10 Follow the instructions in "Closing the server case" on page 30. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
www.gateway.com
47
4
Pull the power supply module straight out of the server with the handle. It may take
considerable force to remove.
5
Push the new power supply module into the server, with the retaining clip on the right,
until it locks into place.
6
Reconnect the AC power cord for the new power supply module.
Replacing the power cage
To replace the power cage:
1
Follow the instructions in
“Preventing static electricity discharge” on page 28
. Make sure
that you turn off the server, then unplug the power cord(s) and all other cables connected
to the server.
2
Follow the instructions in
“Opening the server case” on page 29
.
3
Remove the power supply modules by following the instructions in
“Replacing a power
supply module” on page 46
.
4
Disconnect the main power, CPU power, and power signal cables from the system board.
See
“System board” on page 4
for the location of the connectors on the system board.
5
Remove the screws (3) holding the power cage in the chassis.
6
Slide the power cage (4) toward the front of the chassis to disengage the locking tabs, then
lift the power cage out of the chassis.
7
Place the new power cage into the chassis, aligning the cage with the locking tabs in the
chassis, then slide the power cage toward the back of the chassis to engage the locking tabs.
8
Replace the screws you previously removed, then connect the cables to the system board.
9
Reinstall the power supply modules by following the instructions in
“Replacing a power
supply module” on page 46
.
10
Follow the instructions in
“Closing the server case” on page 30
.