Haier QFD15ESSNWW Installation Instructions - Page 20

Before You Begin, Standard Rear Exhaust, Recommended Configuration To, Minimize Exhaust Blockage,

Get Haier QFD15ESSNWW PDF manuals and user guides View all Haier QFD15ESSNWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

ENGLISH INSTALLATION INSTRUCTIONS EXHAUSTING THE DRYER (cont.) EXHAUST SYSTEM CHECKLIST HOOD OR WALL CAP • Terminate in a manner to prevent back drafts or entry of birds or other wildlife. • Termination should present minimal resistance to the exhaust airflow and should require little or no maintenance to prevent clogging. • Wall caps must be installed at least 12" above ground level or any other obstruction with the opening pointed down. SEPARATION OF TURNS • For best performance, separate all turns by at least 4 ft. of straight duct, including distance between last turn and dampened exhaust hood (wall cap). SEALING OF JOINTS • All joints should be tight to avoid leaks. The male end of each section of duct must point away from the dryer. • Duct joints should be made air- and moisture-tight by wrapping the overlapped joints with duct tape or aluminum tape. • Do not assemble ductwork with any fasteners that extend into the duct. These fasteners can accumulate lint, creating a potential fire hazard. • Horizontal runs should slope down towards the outdoors 1/4" per foot. • Provide an access for inspection and cleaning of the exhaust system, especially at turns and joints. Exhaust system shall be inspected and cleaned at least once a year. INSULATION • Ductwork that runs through an unheated area or is near air conditioning should be insulated to reduce condensation and lint build-up. BEFORE YOU BEGIN • Remove and discard existing plastic or metal foil duct and replace with UL-listed duct. • Remove any lint from the wall exhaust opening. STANDARD REAR EXHAUST We recommend that you install your dryer before installing your washer. This will permit direct access for easier exhaust connection. Slide the end of the exhaust duct on the back of the dryer and secure with duct tape or a hose clamp. Duct NOTE: We strongly recommend using rigid metal exhaust duct. However, if flexible ducting is used it must be UL-Listed metal, not plastic. • For straight line installation, connect the dryer exhaust to the external exhaust hood using duct tape or clamp. Wall Side Duct Tape Dryer Side RECOMMENDED CONFIGURATION TO MINIMIZE EXHAUST BLOCKAGE Using duct elbows will prevent duct kinking and collapsing. Internal Duct Opening Wall Check that exhaust hood damper opens and closes freely. Wall Transition Ducting 20 49-3000195

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
20
49-3000195
ENGLISH
INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN
•
Remove and discard existing plastic or metal foil duct
and replace with UL-listed duct.
•
Remove any lint from the wall exhaust opening.
Internal
Duct
Opening
Wall
Check that exhaust
hood damper opens
and closes freely.
STANDARD REAR EXHAUST
We recommend that you install your dryer before
installing your washer. This will permit direct access
for easier exhaust connection.
Slide the end of the exhaust duct on the back of the
dryer and secure with duct tape or a hose clamp.
NOTE:
We strongly recommend using rigid metal
exhaust duct. However, if flexible ducting is used it must
be UL-Listed metal, not plastic.
•
For straight line installation, connect the dryer
exhaust to the external exhaust hood using duct tape
or clamp.
RECOMMENDED CONFIGURATION TO
MINIMIZE EXHAUST BLOCKAGE
Using duct elbows will prevent duct kinking and
collapsing.
EXHAUST SYSTEM CHECKLIST
HOOD OR WALL CAP
•
Terminate in a manner to prevent back drafts or entry of
birds or other wildlife.
•
Termination should present minimal resistance to
the exhaust airflow and should require little or no
maintenance to prevent clogging.
•
Wall caps must be installed at least 12” above ground
level or any other obstruction with the opening pointed
down.
SEPARATION OF TURNS
•
For best performance, separate all turns by at least
4
ft. of straight duct, including distance between last
turn and dampened exhaust hood (wall cap).
SEALING OF JOINTS
•
All joints should be tight to avoid leaks. The male end of
each section of duct must point away from the dryer.
•
Duct joints should be made air- and moisture-tight
by wrapping the overlapped joints with duct tape or
aluminum tape.
•
Do not assemble ductwork with any fasteners that
extend into the duct. These fasteners can accumulate
lint, creating a potential fire hazard.
•
Horizontal runs should slope down towards the
outdoors 1/4” per foot.
•
Provide an access for inspection and cleaning of
the exhaust system, especially at turns and joints.
Exhaust system shall be inspected and cleaned at
least once a year.
INSULATION
•
Ductwork that runs through an unheated area or is
near air conditioning should be insulated to reduce
condensation and lint build-up.
Wall Side
Dryer
Side
Duct Tape
EXHAUSTING THE DRYER (cont.)
Duct
Transition
Ducting
Wall