HP 6120XG HP ProCurve Series 6120 Blade Switches IPv6 Configuration Guide - Page 150

Syntax, ipv6-address, link-local-address, vlan-id, hostname, Default, Range

Get HP 6120XG PDF manuals and user guides View all HP 6120XG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

IPv6 Diagnostic and Troubleshooting Traceroute for IPv6 Syntax: traceroute6 < ipv6-address | hostname > [minttl < 1-255 > [maxttl < 1-255 > [timeout < 1 - 60 >] [probes < 1-5 >] [source < ipv6-addr | vid > traceroute6 [minttl < 1-255 >] [maxttl < 1-255 >] [timeout < 1 - 60 >] [probes < 1-5 >] [source < ipv6-addr | vid > Lists the IPv6 address of each hop in the route to the specified destination host device with the time (in microseconds) required for a packet reply to be received from each next-hop device. : IPv6 address of a destination host device. %vlan: IPv6 link-local address, where %vlan specifies the VLAN ID number. : Host name of an IPv6 host device configured on an IPv6 DNS server. minttl: Minimum number of hops allowed for each probe packet sent along the route. Default: 1; Range: 1 - 255. • If the minttl value is greater than the actual number of hops, the traceroute output displays only the hops equal to or greater than the configured minttl threshold value. The hops below the threshold value are not displayed. • If the minttl value is the same as the actual number of hops, only the final hop is displayed in the command output. • If the minttl value is less than the actual number of hops, all hops to the destination host are displayed. maxttl: Maximum number of hops allowed for each probe packet sent along the route. Valid values: 1 - 255. Default: 30. • If the maxttl value is less than the actual number of hops required to reach the host, the traceroute output displays only the IPv6 addresses of the hops detected by the configured maxttl value. timeout: Number of seconds within which a response is required from the IPv6 device at each hop in the route to the destination host before the traceroute operation times out. Default: 5 seconds; Range: 1 - 60. probes: Number of times a traceroute is performed to locate the IPv6 device at any hop in the route to the specified host before the operation times out. Default: 3; Range: 1 - 5. [source < ipv6-addr | vid >]: The source IPv6 address or VLAN of the traceroute device or the VLAN-ID on which the traceroute packet is being sent. 7-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
7-6
IPv6 Diagnostic and Troubleshooting
Traceroute for IPv6
Syntax:
traceroute6 <
ipv6-address
|
hostname
>
[minttl < 1-255 > [maxttl < 1-255 >
[timeout < 1 - 60 >] [probes < 1-5 >] [source <
ipv6-addr
|
vid
>
traceroute6 <
link-local-address
%vlan<
vid
> |
hostname
>
[minttl < 1-255 >] [maxttl < 1-255 >]
[timeout < 1 - 60 >] [probes < 1-5 >] [source <
ipv6-addr
|
vid
>
Lists the IPv6 address of each hop in the route to the specified
destination host device with the time (in microseconds)
required for a packet reply to be received from each next-hop
device.
<
ipv6-address
>:
IPv6 address of a destination host device.
<
link-local-address
>%vlan<
vlan-id
>:
IPv6 link-local address,
where
%vlan<
vlan-id
>
specifies the VLAN ID number.
<
hostname
>:
Host name of an IPv6 host device configured on
an IPv6 DNS server.
minttl:
Minimum number of hops allowed for each probe
packet sent along the route.
Default:
1;
Range:
1 - 255.
•
If the
minttl
value is greater than the actual number of hops,
the traceroute output displays only the hops equal to or
greater than the configured
minttl
threshold value. The
hops below the threshold value are not displayed.
•
If the
minttl
value is the same as the actual number of hops,
only the final hop is displayed in the command output.
•
If the
minttl
value is less than the actual number of hops,
all hops to the destination host are displayed.
maxttl
:
Maximum number of hops allowed for each probe
packet sent along the route. Valid values: 1 - 255. Default: 30.
•
If the
maxttl
value is less than the actual number of hops
required to reach the host, the traceroute output displays
only the IPv6 addresses of the hops detected by the
configured
maxttl
value.
timeout
:
Number of seconds within which a response is
required from the IPv6 device at each hop in the route to the
destination host before the traceroute operation times out.
Default:
5 seconds;
Range:
1 - 60.
probes
:
Number of times a traceroute is performed to locate
the IPv6 device at any hop in the route to the specified host
before the operation times out.
Default:
3;
Range:
1 - 5.
[source <
ipv6-addr
|
vid
>]:
The source IPv6 address or VLAN
of the traceroute device or the VLAN-ID on which the
traceroute packet is being sent.