HP 6120XG HP ProCurve Series 6120 Blade Switches IPv6 Configuration Guide - Page 154

Viewing the Current Configuration, Operating Notes,

Page 154 highlights

IPv6 Diagnostic and Troubleshooting DNS Resolver for IPv6 been configured as the domain name on the switch and the address of a DNS server residing in that domain is also configured on the switch. The commands for these steps are as follows: ProCurve(config)# ip dns server priority 1 2001:db8::127:10 ProCurve(config)# ip dns domain-name mygroup.procurve.net ProCurve(config)# ping6 mars-1 fe80::215:60ff:fe7a:adc0 is alive, time = 1 ms Figure 7-1. Example of Configuring for a Local DNS Server and Pinging a Registered Device However, for the same "mars-1" device, if mygroup.procurve.net was not the configured domain name, you would have to use the fully qualified domain name for the device named mars-1: ProCurve# ping6 mars-1.mygroup.procurve.net For further information and examples on using the DNS feature, refer to "DNS Resolver" in appendix C, "Troubleshooting", in the current Management and Configuration Guide for your switch. Viewing the Current Configuration Use the show ip dns command to view the current DNS server configuration. Use the show run command to view both the current DNS server addresses and the current DNS domain name in the active configuration. Operating Notes DNS addressing is not configurable from a DHCPv6 server. 7-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167

7-10
IPv6 Diagnostic and Troubleshooting
DNS Resolver for IPv6
been configured as the domain name on the switch and the address of a DNS
server residing in that domain is also configured on the switch. The commands
for these steps are as follows:
Figure 7-1.
Example of Configuring for a Local DNS Server and Pinging a Registered Device
However, for the same “mars-1” device, if mygroup.procurve.net was not the
configured domain name, you would have to use the fully qualified domain
name for the device named mars-1:
ProCurve# ping6 mars-1.mygroup.procurve.net
For further information and examples on using the DNS feature, refer to “DNS
Resolver” in appendix C, “Troubleshooting”, in the current
Management and
Configuration Guide
for your switch.
Viewing the Current Configuration
Use the
show ip dns
command to view the current DNS server configuration.
Use the
show run
command to view both the current DNS server addresses
and the current DNS domain name in the active configuration.
Operating Notes
DNS addressing is not configurable from a DHCPv6 server.
ProCurve(config)# ip dns server priority 1 2001:db8::127:10
ProCurve(config)# ip dns domain-name mygroup.procurve.net
ProCurve(config)# ping6 mars-1
fe80::215:60ff:fe7a:adc0 is alive, time = 1 ms