HP Brio 83xx HP BRIO PC - Online Reference Guide, Not Orderable - Page 53

Removing an Expansion Card, Removing a Card

Get HP Brio 83xx PDF manuals and user guides View all HP Brio 83xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

3 Upgrading and Adding Accessories Adding Accessories Removing an Expansion Card You might need to remove an expansion card to install a component on it, or to improve access to components on the system board. Removing a Card 1 Follow steps 1 to 3 of "Installing an Expansion Card" on page 50. 2 Unscrew and remove the retaining screw securing the card. Keep the retaining screw. 3 Carefully remove the card from its connector, handling the card at each end by its top edge. If the card is tight, loosen the screws on the adjacent slots. Do not bend the card. If you intend to replace the card later, note which connector it is in. 4 With its components facing up, place the card on a clean, flat, solid, static-free surface. Handle the card by its edges. 5 Install any new accessories. 6 Replace the expansion card if necessary (refer to steps 5 and 6 on pages 50 and 51). If you do not replace the card, remember to insert a faceplate. 7 Return the computer to the upright position, then replace the cover. Reconnect the power cords and any telecommunications cables. Turn on the display, and then turn on the computer. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
53
3
Upgrading and Adding Accessories
Adding Accessories
Removing an Expansion Card
You might need to remove an expansion card to install a component on it, or to improve access to components on the
system board.
Removing a Card
1
Follow steps
1
to
3
of
“
Installing an Expansion Card
” on page 50
.
2
Unscrew and remove the retaining screw securing the card. Keep the retaining screw.
3
Carefully remove the card from its connector, handling the card at each end by its top edge. If the card is tight, loosen
the screws on the adjacent slots. Do not bend the card. If you intend to replace the card later, note which connector it
is in.
4
With its components facing up, place the card on a clean, flat, solid, static-free surface. Handle the card by its edges.
5
Install any new accessories.
6
Replace the expansion card if necessary (refer to steps
5
and
6
on pages
50
and
51
).
If you do not replace the card, remember to insert a faceplate.
7
Return the computer to the upright position, then replace the cover. Reconnect the power cords and any
telecommunications cables. Turn on the display, and then turn on the computer.