HP Color LaserJet Pro 4201-4203cdn User Guide 1 - Page 66

Link speed and duplex settings, Settings, Network, Ethernet Settings, Wireless Settings

Page 66 highlights

1. At the printer control panel, rotate the control dial to select the Menu option, and then press the dial. 2. Rotate the dial to select Settings, and then press the dial. 3. Rotate the dial to select Network , and then press the dial to open the network settings list. 4. Rotate the dial to select one of the following menus, and then press the dial. ● Ethernet Settings (for a wired network) ● Wireless Settings (for a wireless network) 5. Adjust the settings as needed. Link speed and duplex settings The link speed and communication mode of the print server must match the network hub. For most situations, leave the printer in automatic mode. Incorrect changes to the link speed and duplex settings might prevent the printer from communicating with other network devices. If you need to make changes, use the printer control panel. NOTE: This information applies only to Ethernet (wired) networks. It does not apply to wireless networks. NOTE: The printer setting must match the setting for the network device (a network hub, switch, gateway, router, or computer). NOTE: Making changes to these settings causes the printer to turn off and then on. Make changes only when the printer is idle. 1. At the printer control panel, rotate the control dial to select the Menu option, and then press the dial. 2. Rotate the dial to select Settings, and then press the dial. 3. Rotate and press the dial to open the following menus: a. Network Settings b. Ethernet Settings c. Link Speed 4. Rotate the dial to select one of the following options: Table 5-2 Link Speed settings Setting Description 10 Mb Half 10 Mb Full 10 Mbps, half-duplex operation 10 Mbps, full-duplex operation 100 Mb Half 100 Mbps, half-duplex operation 100 Mb Full 1000 Mb Full Automatic 100 Mbps, full-duplex operation 1000 Mbps, full-duplex operation The print server automatically configures itself for the highest link speed and communication mode allowed on the network. Link speed and duplex settings 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148

1.
At the printer control panel, rotate the control dial to select the
Menu
option, and then press the dial.
2.
Rotate the dial to select
Settings
, and then press the dial.
3.
Rotate the dial to select
Network
, and then press the dial to open the network settings list.
4.
Rotate the dial to select one of the following menus, and then press the dial.
Ethernet Settings
(for a wired network)
Wireless Settings
(for a wireless network)
5.
Adjust the settings as needed.
Link speed and duplex settings
The link speed and communication mode of the print server must match the network hub. For most
situations, leave the printer in automatic mode. Incorrect changes to the link speed and duplex settings
might prevent the printer from communicating with other network devices. If you need to make changes,
use the printer control panel.
NOTE:
This information applies only to Ethernet (wired) networks. It does not apply to wireless
networks.
NOTE:
The printer setting must match the setting for the network device (a network hub, switch,
gateway, router, or computer).
NOTE:
Making changes to these settings causes the printer to turn off and then on. Make changes
only when the printer is idle.
1.
At the printer control panel, rotate the control dial to select the
Menu
option, and then press the dial.
2.
Rotate the dial to select
Settings
, and then press the dial.
3.
Rotate and press the dial to open the following menus:
a.
Network Settings
b.
Ethernet Settings
c.
Link Speed
4.
Rotate the dial to select one of the following options:
Table 5-2
Link Speed settings
Setting
Description
10 Mb Half
10 Mbps, half-duplex operation
10 Mb Full
10 Mbps, full-duplex operation
100 Mb Half
100 Mbps, half-duplex operation
100 Mb Full
100 Mbps, full-duplex operation
1000 Mb Full
1000 Mbps, full-duplex operation
Automatic
The print server automatically configures itself for the
highest link speed and communication mode allowed on
the network.
Link speed and duplex settings
57