HP ENVY 15-ar000 Maintenance and Service Guide - Page 42

Solid-state drive, Remove the solid-state drive

Get HP ENVY 15-ar000 PDF manuals and user guides View all HP ENVY 15-ar000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Solid-state drive Description Spare part number 256-MB, M2.2280, PCIe 3×4SS, NVMe, solid-state drive supporting TLC (for use only on computer models 847109-001 equipped with an AMD A9-9410 processor) Before removing the solid-state drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 24). 5. Disconnect the battery cable from the system board (see Battery on page 26). Remove the solid-state drive: 1. Remove the Phillips PM2.0×3.8 screw (1) that secures the solid-state drive to the computer. (The solid- state drive tilts up.) 2. Remove the solid-state drive (2) by pulling the drive away from the slot at an angle. Reverse this procedure to install the solid-state drive. 34 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Solid-state drive
Description
Spare part number
256-MB, M2.2280, PCIe 3×4SS, NVMe, solid-state drive supporting TLC (for use only on computer models
equipped with an AMD A9-9410 processor)
847109-001
Before removing the solid-state drive, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
24
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
26
).
Remove the solid-state drive:
1.
Remove the Phillips PM2.0×3.8 screw
(1)
that secures the solid-state drive to the computer. (The solid-
state drive tilts up.)
2.
Remove the solid-state drive
(2)
by pulling the drive away from the slot at an angle.
Reverse this procedure to install the solid-state drive.
34
Chapter 5
Removal and replacement procedures