HP ENVY x2 - 15t-c000 HP ENVY x2 Detachable PC Maintenance and Service Guide - Page 63

Power connector, Remove the 12 Phillips PM2.0×3.0 screws

Page 63 highlights

Power connector NOTE: Clean bench required to assemble with display. Description Power connector NOTE: Clean bench required to assemble with display. Spare part number 783095-001 Before removing the power connector, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the following components from the tablet: ● Rear cover (see Rear cover on page 29). ● Vibration board (see Vibration board on page 33). ● Audio/SD board (see Audio/SD board on page 34). ● Battery (see Battery on page 35). ● POGO board (see POGO board on page 36). ● Display cable (see Display cable on page 37). ● Heat sink (see Heat sink on page 38). ● Hard drive (see Hard drive on page 39). ● WLAN module (see WLAN/Bluetooth combo card on page 41). ● Webcam (see Webcam on page 43). ● Speakers (see Speakers on page 44). ● Power button board (see Power button board on page 46). ● Volume board (see Volume board on page 47). ● Touch screen board (see Touch screen board on page 48). ● Antennas (see Antennas on page 49). ● System board (see System board on page 50). Remove the power connector: 1. Remove the 12 Phillips PM2.0×3.0 screws (1) that secure the large bracket to the display. 2. Lift the large bracket from atop the display (2). Component replacement procedures 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82

Power connector
NOTE:
Clean bench required to assemble with display.
Description
Spare part number
Power connector
NOTE:
Clean bench required to assemble with display.
783095-001
Before removing the power connector, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the following components from the tablet:
Rear cover (see
Rear cover
on page
29
).
Vibration board (see
Vibration board
on page
33
).
Audio/SD board (see
Audio/SD board
on page
34
).
Battery (see
Battery
on page
35
).
POGO board (see
POGO board
on page
36
).
Display cable (see
Display cable
on page
37
).
Heat sink (see
Heat sink
on page
38
).
Hard drive (see
Hard drive
on page
39
).
WLAN module (see
WLAN/Bluetooth combo card
on page
41
).
Webcam (see
Webcam
on page
43
).
Speakers (see
Speakers
on page
44
).
Power button board (see
Power button board
on page
46
).
Volume board (see
Volume board
on page
47
).
Touch screen board (see
Touch screen board
on page
48
).
Antennas (see
Antennas
on page
49
).
System board (see
System board
on page
50
).
Remove the power connector:
1.
Remove the 12 Phillips PM2.0×3.0 screws
(1)
that secure the large bracket to the display.
2.
Lift the large bracket from atop the display
(2)
.
Component replacement procedures
53