HP EliteBook 630 Maintenance and Service Guide - Page 57

Fingerprint reader board, Remove the touchpad from the computer

Get HP EliteBook 630 PDF manuals and user guides View all HP EliteBook 630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Before removing the touchpad, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 37). 2. Remove the bottom cover (see Bottom cover on page 37). 3. Remove the battery (see Battery on page 44). Remove the touchpad: 1. Disconnect the system board cable from the ZIF connector on the touchpad (1). 2. Lift the tape off the top of the touchpad (2). 3. Release the keyboard backlight cable from the adhesive that secures it to the top of the touchpad (3). 4. Remove the four Phillips M2.0× 2.0 screws (4) that secure the touchpad to the computer. 5. Remove the two Phillips M1.6 × 2.0 screws (5) that secure the touchpad to the computer. 6. Remove the touchpad from the computer (6). NOTE: If an NFC module is installed, disconnect the NFC antenna cable from the ZIF connector on the NFC module. The antenna is secured to the touchpad. Reverse this procedure to install the touchpad. Fingerprint reader board To remove the fingerprint reader board, use this procedure and illustration. Table 6-6 Fingerprint reader board description and part number Description Fingerprint reader board Fingerprint reader board cable (included in Cable Kit) Spare part number N00879-001 N00097-001 Fingerprint reader board 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Before removing the touchpad, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
37
).
2.
Remove the bottom cover (see
Bottom cover
on page
37
).
3.
Remove the battery (see
Battery
on page
44
).
Remove the touchpad:
1.
Disconnect the system board cable from the ZIF connector on the touchpad
(1)
.
2.
Lift the tape off the top of the touchpad
(2)
.
3.
Release the keyboard backlight cable from the adhesive that secures it to the top of the touchpad
(3)
.
4.
Remove the four Phillips M2.0× 2.0 screws
(4)
that secure the touchpad to the computer.
5.
Remove the two Phillips M1.6 × 2.0 screws
(5)
that secure the touchpad to the computer.
6.
Remove the touchpad from the computer
(6)
.
NOTE:
If an NFC module is installed, disconnect the NFC antenna cable from the ZIF connector on the
NFC module. The antenna is secured to the touchpad.
Reverse this procedure to install the touchpad.
Fingerprint reader board
To remove the fingerprint reader board, use this procedure and illustration.
Table 6-6
Fingerprint reader board description and part number
Description
Spare part number
Fingerprint reader board
N00879-001
Fingerprint reader board cable (included in Cable Kit)
N00097-001
Fingerprint reader board
49