HP EliteDesk 800 G4 Maintenance and Service Guide - Page 121

Beep error code sequences occur for

Get HP EliteDesk 800 G4 PDF manuals and user guides View all HP EliteDesk 800 G4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

4 Thermal 5 System board Patterns of blink/beep codes are determined by using the following parameters: ● 1 second pause occurs after the last major blink. ● 2 second pause occurs after the last minor blink. ● Beep error code sequences occur for the first 5 iterations of the pattern and then stop. ● Blink error code sequences continue until the computer is unplugged or the power button is pressed. NOTE: Not all diagnostic lights and audible codes are available on all models. The red LED blinks to represent the major error category (long blinks). The white LED blinks to represent the minor error category (short blinks). For example, '3.5' indicates 3 long red blinks and 5 short white blinks to communicate the processor is not detected. Category Major/minor code Description BIOS 2.2 The main area (DXE) of BIOS has become corrupted and there is no recovery binary image available. 2.3 The embedded controller policy requires the user to enter a key sequence. 2.4 The embedded controller is checking or recovering the boot block. Hardware 3.2 The embedded controller has timed out waiting for BIOS to return from memory initialization. 3.3 The embedded controller has timed out waiting for BIOS to return from graphics initialization. 3.4 The system board displays a power failure (crowbar).* 3.5 The processor is not detected.* 3.6 The processor does not support an enabled feature. Thermal 4.2 A processor over temperature condition has been detected.* 4.3 An ambient temperature over temperature condition has been detected. 4.4 An MXM over temperature condition has been detected. System board 5.2 The embedded controller cannot find valid firmware. 5.3 The embedded controller has timed out waiting for the BIOS. 5.4 The embedded controller has timed out waiting for BIOS to return from system board initialization. 5.5 The embedded controller rebooted the system after a possible lockup condition had been detected through the use of a System Health Timer, Automated System Recovery Timer, or other mechanism. * Indicates hardware triggered event; all other events are controlled by the BIOS. Interpreting system validation diagnostic front panel LEDs and audible codes 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
4
Thermal
5
System board
Patterns of blink/beep codes are determined by using the following parameters:
●
1 second pause occurs after the last major blink.
●
2 second pause occurs after the last minor blink.
●
Beep error code sequences occur for the
first
5 iterations of the pattern and then stop.
●
Blink error code sequences continue until the computer is unplugged or the power button is pressed.
NOTE:
Not all diagnostic lights and audible codes are available on all models.
The red LED blinks to represent the major error category (long blinks). The white LED blinks to represent the
minor error category (short blinks). For example, ‘3.5’ indicates 3 long red blinks and 5 short white blinks to
communicate the processor is not detected.
Category
Major/minor code
Description
BIOS
2.2
The main area (DXE) of BIOS has become corrupted and there is no recovery
binary image available.
2.3
The embedded controller policy requires the user to enter a key sequence.
2.4
The embedded controller is checking or recovering the boot block.
Hardware
3.2
The embedded controller has timed out waiting for BIOS to return from
memory initialization.
3.3
The embedded controller has timed out waiting for BIOS to return from
graphics initialization.
3.4
The system board displays a power failure (crowbar).*
3.5
The processor is not detected.*
3.6
The processor does not support an enabled feature.
Thermal
4.2
A processor over temperature condition has been detected.*
4.3
An ambient temperature over temperature condition has been detected.
4.4
An MXM over temperature condition has been detected.
System board
5.2
The embedded controller cannot
find
valid
firmware.
5.3
The embedded controller has timed out waiting for the BIOS.
5.4
The embedded controller has timed out waiting for BIOS to return from
system board initialization.
5.5
The embedded controller rebooted the system after a possible lockup
condition had been detected through the use of a System Health Timer,
Automated System Recovery Timer, or other mechanism.
* Indicates hardware triggered event; all other events are controlled by the BIOS.
Interpreting system validation diagnostic front panel LEDs and audible codes
113