HP EliteDesk 800 G4 Maintenance and Service Guide - Page 42

Removing a 3.5-inch hard drive, drive bay.

Get HP EliteDesk 800 G4 PDF manuals and user guides View all HP EliteDesk 800 G4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

6. Connect the power cable and data cable to the rear of the drive. 7. Connect the opposite end of the data cable to one of the light-blue SATA connectors on the system board labeled SATA1 or SATA2. NOTE: Refer to System board connections on page 22 for an illustration of the system board drive connectors. 8. Reassemble the computer. Removing a 3.5-inch hard drive NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. There are two 3.5-inch hard drive bays. The procedure for removing a 3.5-inch hard drive is the same for each drive bay. 1. Prepare the computer for disassembly (Preparation for disassembly on page 17). 2. Remove the access panel (Access panel on page 18). 3. Disconnect the power cable (1) and data cable (2) from the rear of the hard drive. 34 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
6.
Connect the power cable and data cable to the rear of the drive.
7.
Connect the opposite end of the data cable to one of the light-blue SATA connectors on the system board
labeled SATA1 or SATA2.
NOTE:
Refer to
System board connections
on page
22
for an illustration of the system board drive
connectors.
8.
Reassemble the computer.
Removing a 3.5-inch hard drive
NOTE:
Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you
can transfer the data to the new hard drive.
There are two 3.5-inch hard drive bays. The procedure for removing a 3.5-inch hard drive is the same for each
drive bay.
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
17
).
2.
Remove the access panel (
Access panel
on page
18
).
3.
Disconnect the power cable (1) and data cable (2) from the rear of the hard drive.
34
Chapter 4
Removal and replacement procedures