HP EliteDesk 800 G4 Maintenance and Service Guide - Page 51

Rotate the drive cage back down to its normal position, Reassemble the computer.

Get HP EliteDesk 800 G4 PDF manuals and user guides View all HP EliteDesk 800 G4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

6. Align the mounting screws on the drive with the J-slots on the sides of the drive bay. Press the drive into the drive bay, and then slide the drive forward until it locks in place. 7. Connect the power cable (1) and data cable (2) to the rear of the hard drive. NOTE: If the 2.5-inch hard drive is the primary drive, connect the other end of the data cable to the dark-blue SATA connector on the system board labeled SATA0. If it is a secondary hard drive, connect the other end of the data cable to one of the light-blue SATA connectors on the system board. 8. Rotate the drive cage back down to its normal position (Drive cage on page 40). 9. Reassemble the computer. Drives 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
6.
Align the mounting screws on the drive with the J-slots on the sides of the drive bay. Press the drive into
the drive bay, and then slide the drive forward until it locks in place.
7.
Connect the power cable (1) and data cable (2) to the rear of the hard drive.
NOTE:
If the 2.5-inch hard drive is the primary drive, connect the other end of the data cable to the
dark-blue SATA connector on the system board labeled SATA0. If it is a secondary hard drive, connect the
other end of the data cable to one of the light-blue SATA connectors on the system board.
8.
Rotate the drive cage back down to its normal position (
Drive cage
on page
40
).
9.
Reassemble the computer.
Drives
43