HP EliteDesk 800 G5 Maintenance and Service Guide - Page 64

Optional rear port

Get HP EliteDesk 800 G5 PDF manuals and user guides View all HP EliteDesk 800 G5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Optional rear port The optional rear port is attached to the rear of the chassis with two screws. To remove the optional rear port: 1. Prepare the computer for disassembly (Preparation for disassembly on page 18). 2. Remove the access panel (Access panel on page 19). 3. Remove the air duct (Air duct on page 52). 4. Disconnect the cable from the system board connector labeled COMA (1). 5. Remove the two hex nut jack screws (2) that secure the port to the rear of the chassis. 6. Remove the port from the computer (3). To install the optional rear port, reverse the removal procedures. 54 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
Optional rear port
The optional rear port is attached to the rear of the chassis with two screws.
To remove the optional rear port:
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
18
).
2.
Remove the access panel (
Access panel
on page
19
).
3.
Remove the air duct (
Air duct
on page
52
).
4.
Disconnect the cable from the system board connector labeled COMA
(1)
.
5.
Remove the two hex nut jack screws
(2)
that secure the port to the rear of the chassis.
6.
Remove the port from the computer
(3)
.
To install the optional rear port, reverse the removal procedures.
54
Chapter 4
Removal and replacement procedures